Kitronik Rear Bike Light Manual Download Page 8

Page: 8 / 8

This easy build bike light kit has just ten
parts, making it a good introduction to
electronics. The kit uses two ultra
bright red LEDs, which flash rapidly,
providing a highly visible light. Making it
ideal for use as a rear bike light.

Note: We recommend this rear bike
light is used in conjunction with a
commercially available light.

For more information on RoHS and CE please visit kitronik.co.uk/rohs-ce. Children

assembling this product should be supervised by a competent adult. The product contains

small parts so should be kept out of reach of children under 3 years old.

WARNING

Contents may inspire creativity

0845 8380781

www.kitronik.co.uk

[email protected]

TOOLS REQUIRED:

- Soldering Iron

- Solder

- Wire Cutters

KIT REQUIRES

2 x AA batteries

STOCK CODE

2106 or 1006 (Retail Version)

INSTRUCTIONS:

This booklet contains build instructions

and a circuit explanation. For more

detailed resources please visit our

website at www.kitronik.co.uk/2106

Designed & manufactured
in the UK by

Example

Use

kitronik.co.uk/twitter

kitronik.co.uk/facebook
kitronik.co.uk/youtube
kitronik.co.uk/google

Summary of Contents for Rear Bike Light









Search results

Summary of Contents for Rear Bike Light

Reviews:

Related manuals for Rear Bike Light

Brands by name

Popular brands

Kitronik Rear Bike Light, Manual

Search results

Summary of Contents for Rear Bike Light

Reviews:

Related manuals for Rear Bike Light

Brands by name

Popular brands