![background image](http://html.mh-extra.com/html/kitchenaid/ksdg950ess2/ksdg950ess2_installation-instructions-manual_198316004.webp)
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■
Tape measure
■
Phillips
screwdriver
■
Flat-blade
screwdriver
■
1/8" (3 mm) flat-
blade screwdriver
■
Level
■
Drill
■
Adjustable wrench
■
Slip joint pliers
■
Pipe wrench
■
15⁄16" (2.4 cm)
combination
wrench
■
1/8" (3.2 mm)
drill bit (for wood
floors)
■
Marker or pencil
■
5¹⁄
2
" (14 cm) hole saw (round
ducting)
■
Saw for 3¹⁄
4
" x 10" (8.3 x
25.4 cm) rectangle vent
■
#2 square bit and driver
■
Flashlight
■
Masking tape
■
Pipe-joint compound resistant
to natural and Propane gases
■
3⁄16" (4.8 mm) carbide-tipped
masonry drill bit (for concrete/
ceramic floors)
■
Noncorrosive leak-detection
solution
■
Sheet metal aluminum tape
For Propane/Natural Gas
Conversions
■
1/2" (1.3 cm) combination
wrench
■
1/4" (6 mm) nut driver
■
9/32" (7 mm) nut driver
Parts Supplied
Check that all parts are included.
■
Propane/Natural gas conversion kit (dual fuel models only)
■
Blower mounting/venting template
■
Grease filter (packaged in place)
■
Oven racks (3)
■
Blower motor kit (under unit)
■
Blower cover kit (packed in cavity)
■
10-32 hex nuts (attached to terminal block) (3)
■
Direct wire lugs (3)
■
#12 x 1
5
⁄
8
" (4.1 cm) screws (for mounting anti-tip bracket) (2)
■
Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall
or floor. Thickness of flooring may require longer screws
to anchor bracket to subfloor. Longer screws are available
from your local hardware store.
Parts Needed
■
Use an approved vent cap for proper performance. If an
alternate wall or roof cap is used, be certain the cap size
is not reduced and that it has a backdraft damper.
■
After determining your vent installation, one of the following
is needed:
5" (12.7 cm) Round surface wall cap damper –
Order Part Number A405.
6" (15.2 cm) Round surface wall cap damper –
Order Part Number A406.
NOTE:
If using 6" (15.2 cm) round venting, you will need
a 5" (12.7 cm) to 6" (15.2 cm) round vent transition.
3¼" x 10" (8.3 x 25.4 cm) Surface wall cap damper –
Order Part Number A403.
To order, see the “Assistance or Service” section of the Use and
Care Guide:
– Metal ducting
– Vent clamp
– Aluminum foil tape
Check local codes and consult gas supplier. Check existing
gas supply and electrical supply. See the appropriate “Electrical
Requirements” and “Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by
a licensed, qualified electrical installer.
Optional Parts
To purchase these or any other accessories, please reference
the “Accessories” section of the Use and Care Guide for
contact information.
■
Side Trim Kits:
5/8" (1.7 cm) Black – Order Part Number W10675026
5/8" (1.7 cm) Stainless Steel – Order Part Number
W10675028
1¹⁄
8
" (2.9 cm) Black – Order Part Number W10731886
1¹⁄
8
" (2.9 cm) Stainless Steel – Order Part Number
W10731887
■
Backsplash Kits:
High 6" (15.2 cm) Black – Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel – Order Part Number
W10655450