background image

24 

 

TIPS FOR OUTDOOR GRILLING 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Before Grilling 

 

  Thaw food items before grilling. 

   Preheat grill on high (use all grill burners) 10 minutes. The 

hood must be closed during preheating, There is no need 
to use the back rotisserie burner for preheating. Preheating 
provides the high heat needed to brown and seal the 
juices. 

  Shorten the preheat time when grilling high-fat cuts of meat 

or poultry, such as chicken thighs. This will help reduce 
flare-ups. 

  Lightly oil the grill grates or the food when cooking low-fat 

cuts of meat, fish or poultry, such as lean hamburger 
patties, shrimp or skinless chicken breasts. 

  Using too much oil can cause gray ash to deposit on food. 

  Trim excess fat from meats prior to cooking to reduce 

flare-ups. 

  Make vertical cuts at 2" (5 cm) intervals around the fat 

edge of meat to avoid curling. 

  Add seasoning or salt only after the cooking is finished. 

 

During Grilling

 

 

  Turn foods only once. Juices are lost when meat is turned 

several times. 

  Turn meat just when juices begin to appear on the surface. 

  Avoid puncturing or cutting the meats to test doneness. 

This allows juices to escape. 

  It may be necessary to lower the heat setting for foods 

that cook a long time or are marinated or basted in a 
sugary sauce. 

  It using a high flame, add barbecue sauce only during the 

last 10 minutes of cooking to avoid burning the sauce. 

  The degree at doneness is influenced by the type of meat, 

cut of meat (size, shape and thickness), heat setting 
selected, and length of time on the grill. 

  Cooking time will be longer with an open grill cover. 

 

 

Cooking Methods 

For optimal use of the SureSear™ system, the following cooking 
methods are recommended. 

Direct Heat

 

Cooking by direct heat means the food is placed on grill grates 
directly above lighted burners. Hood position can be up or down. 
If hood is in the up position, total cooking times may be longer. 
Direct heat sears the food. Searing is a process that seals natural 
juices in food by cooking with intense heat for a short period of 
time. While juices stay inside, the outside is browned with a 
flavorful grilled coating. 

Indirect Heat

 

For best results, do not select the indirect heat cooking method 
when it is windy. 

Cooking by indirect heat means the food is placed on the grill 
grate above an unheated burner, allowing heat from lighted 
burner(s) on either side to cook the food. 

Turn on 1 burner. Cook with the hood down. This will shorten the 
cooking time. 

 

Indirect Cooking

 

Place food only on the grill grate over the OFF burners. 

 

Grill Size 

Burner 

Burner 

 

 

1

 

2

 

 

20"(50.8cm)grill 

ON 

OFF 

 

 

 

 

 

 

 
 

 

 

Summary of Contents for FREESTANDING OUTDOOR GRILL
































Reviews: