background image

Product dimensions

Cabinet dimensions/requirements

3

Cabinet opening dimensions shown are for:
25" (63.5 cm) countertop depth, 24" (61 cm) base
cabinet depth, 36" (91.4 cm) countertop height

Freestanding Range

Slide-in Range

7/8" (2.2 cm)
min. required
between cutout
and cabinet
door or hinge.

junction box – 8" (20.3 cm) to
22" (55.9 cm) from either
cabinet, 7" (17.8 cm) max. from
floor.

30" (76.2 cm)
opening width

22-3/4" (57.8 cm)
opening depth

4" (10.2 cm) 
min. clearance
from both sides
of range to side
wall or other
combustible
material.

***

NOTE:

24" (61 cm) min. when bottom of wood or metal cabinet is

protected by not less than 1/4" (0.64 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) min. clearance between the top of the cooking platform
and the bottom of an unprotected wood or metal cabinet.

30" (76.2 cm) min.
cabinet opening width

1/2" (1.3 cm)
radius both
corners

For minimum
clearance to
the top of the
cooktop, see

NOTE

.***

18" (45.7 cm)

upper cabinet

to countertop

13" (33 cm) max. 

upper cabinet depth

7/8" (2.2 cm)
min. required
between cutout
and cabinet
door or hinge.

junction box – 
8" (20.3 cm) to 
22" (55.9 cm) from 
either cabinet, 
7" (17.8 cm) max. 
from floor.

30" (76.2 cm)
opening width

4" (10.2 cm) 
min. clearance
from both sides
of range to side
wall or other
combustible
material.

30" (76.2 cm) min.
cabinet opening width

For minimum
clearance to
the top of the
cooktop, see

NOTE

.***

18" (45.7 cm)

upper cabinet

to countertop

13" (33 cm) max. 

upper cabinet depth

Freestanding Range

Slide-in Range

1-1/2"
(3.8 cm)

25-3/4" 

(65.4 cm)

depth with

handle

When installed in a 24" 
(61 cm) base cabinet with 25"
(63.5 cm) countertop — front of
oven door protrudes 1-7/8" (4.8
cm) beyond 24" (61 cm) base
cabinet.

30" 

(76.2 cm)

cooktop

width

36" (91.4 cm) 

cooktop

height with

feet loosened

1-1/2 turns

36" (91.4 cm) 
cooktop
height with
feet loosened
1-1/2 turns

44-3/8"
(112.7 cm) 
overall
height

30" 

(76.2 cm)

cooktop

width

8-1/4"

(21 cm)

27-3/4" 
(70.5 cm)
depth with
handle

22-5/8"

(57.5 cm)

30" 

(76.2 cm)

width

30" 

(76.2 cm)

width

1" 
(2.5 cm)

1" (2.5 cm)
spacer

Summary of Contents for Convection Oven













Reviews: