background image

6

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used, it is 
recommended that a qualified electrical installer determine that 
the ground path and wire gauge are in accordance with local 
codes and that the ground path is adequate.

Check with a qualified electrical installer if you are not sure the 
range is properly grounded.

Do not use an extension cord.

Make sure that the electrical connection and wire size are 
adequate and in conformance with the National Electrical Code, 
ANSI/NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269

Electrical Connection

To properly install your range, you must determine the type of 
electrical connection you will be using and follow the instructions 
provided for it here.

Range must be connected to the proper electrical voltage 
and frequency as specified on the model/serial number rating 
plate. (The model/serial number rating plate is located on the 
right vertical surface of the oven door frame.)

Range must be connected to a grounded metal, permanent 
wiring system.

A 4-wire or 3-wire, single phase, 120/240 volt, 60 Hz., AC 
only electrical supply is required on a separate, 30-amp 
circuit, fused on both sides of the line. 

A time-delay fuse or circuit breaker is recommended. The 
fuse size must not exceed the circuit rating of the range 
specified on the model/serial rating plate located on the right 
vertical surface of the oven door frame. Refer to the figure in 
the “Product Dimensions” section of “Location 
Requirements” section.

The range can be connected directly to the fused disconnect 
(or circuit breaker box) through flexible, or nonmetallic 
sheathed, copper or aluminum cable. The flexible, cable 
extending from the fuse box or circuit breaker box should be 
connected directly to the junction box. See “Make Electrical 
Connection.”

Locate the junction box to allow as much slack as possible 
between the junction box and the range so that the range can 
be moved if servicing is ever necessary. Do not cut the 
conduit.

A UL listed or CSA approved conduit connector must be 
provided at each end of the power supply cable (at the range 
and at the junction box).

Wire sizes and connections must conform with the rating of 
the range (30 amps).

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail 

leads.

2. Connect the aluminum wiring to the added section of 

copper wire using special connectors and/or tools 
designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended 
procedure. Aluminum/copper connection must conform with 
local codes and industry accepted wiring practices.

Electrical Requirements - Canada Only

If codes permit and a separate ground wire is used, it is 
recommended that a qualified electrical installer determine that 
the ground path and wire gauge are in accordance with local 
codes.

Be sure that the electrical connection and wire size are adequate 
and in conformance with the CSA Standard C22.1, Canadian 
Electrical Code, Part 1 - latest edition, and all local codes and 
ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA.

Check with a qualified electrical installer if you are not sure 
the range is properly grounded.

When a 4-wire, single phase 208/240 volt, 60 Hz., AC only 
electrical supply is available, a 30-amp minimum circuit 
protection is required, fused on both sides of the line.

A time-delay fuse or circuit breaker is recommended.

This range is equipped with a CSA International Certified 
Power Cord intended to be plugged into a standard 14-50R 
wall receptacle. Be sure the wall receptacle is within reach of 
range’s final location.

Do not use an extension cord.

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or 
electrical shock.

Summary of Contents for 9760618





























Reviews: