2
3
LED DISPLAY
SPECIFICATIONS
SAFETY CAUTION
SAFETY CAUTION
Blade
Battery
Hair
Clipper
Motor
Battery
Operating voltage: 3.2V
Rotation speed
：
6000±500rpm
3.7V, 2200mAh high-performance environment-friendly battery
Charging time: about 3 hours
Adapter
Operating time with full charge: about 6 hours
Input: AC 110V – 240V 50/60Hz
Output: DC 4.2V---1000mA
Keep the clipper away from moisture; do not submerge in water or liquid.
1. Use this appliance for its intended purpose. Use only on clean, dry hair.
2. Close supervision is necessary when this appliance is by or near children.
3. Use only with accessories included in the package, or those recommended by
the manufacturer.
4. Avoid contact with the eye area. Avoid use near or on open wounds, damaged or
sensitive skin.
5. Except when charging, always unplug from the electrical socket after use.
6. Keep away from water and all liquids and any detergent agents.
7. Do not pull, twist or wrap the cord tightly. Pull on the plug (not the cord) to
remove from power receptacle.
8. Charging should be done in a safe environment (between 0 and 40
℃
); indoors
in a dry place.
9. The charger adaptor must be kept dry at all times.
10. Do not disassemble the product.
1. The blade must be lubricated before and after each use. This will maintain good
condition and will extend its service life.
2. Nonstop usage for hours may cause overheating of blades, reducing the cutting
performance and shortening their life. Should the blades overheat, switch the unit off
for a few minutes to let it cool down; then lubricate the blades.
3. Hair must be clean and dry before cutting. Foreign matter hidden in the hair may
damage the blade edge.
4. Hair may gather inside the blade housing during use. Too much stored hair will
reduce the oscillating ability of the blades and cause malfunctioning. Always clean
away hair in the blade housing before and after each use.
5. Avoid impact of the blade with hard objects as this may cause damage to the
blade teeth.
1. Do not overcharge. It takes 3 hours to charge your trimmer. Charging over 36
hours may shorten the life of the battery.
2. The life of the battery will be shortened if the trimmer remains at less than full
charge for long periods. Charge unused clippers every 3 months to activate the
battery.
3. It is normal for the adapter and the internal parts to become warm when charging.
4. Please remove the battery safely and return it to the specified places when the
battery runs out. Never discard it casually.
OPERATING INSTRUCTIONS
Charging
1. When the power percentage is less than 5%, switch off the clipper to charge.
2. Connect the charging cord to the charging slot at one end of clipper.
3. Confirm that the switch is off and insert the plug.
5. It will automatically stop after a full charge.
6. A full charging takes an estimated 3 hours. The battery function will be at full
capacity after three charges.
Recharging time: 3 hours
11. The product can only be cleaned by cloth with little water or mild soap solution.
12. It’s normal for the product to produce little heat during using or charging.
13. Use or store the trimmer only at room temperature(between 0 and 40
℃
). Avoid
direct sunlight, moisture or heated surfaces and environments.
14. Except for the purpose of charging, always switch off and unplug the adapter
from the wall socket after use.
15. Do not frequently use the clipper plugged without having recharged the battery,
as this may reduce the life of the battery.
Should the following situations occur, unplug and switch off immediately, and send
for examination or repair.
1. The blade, main unit, power cord or attachment comb is damaged.
2. The clipper or the adapter is dropped into water.
3. The clipper is switched off, but the charging indicator does not light up when
plugged into the power source.
The clipper and accessories must be checked regularly to prevent damage and
ensure good performance.
If damage is detected, do not put the device into operation.
After long time constant use or when obstruction happens, the lubrication
reminder will light up.
2 level Motor Speed Display: High level (7000rpm), Low level (6000rpm)
Press the turbo switch to switch between the two levels.
Battery Status Indicator(100%/50%/Low). When battery is low, please charge
the clipper.
