Kisae DMT1230 Owner'S Manual Download Page 4

 

 

REV D

                                                                                                                                                                                                     Page 

4                          

 

 

 
 
 
 

 

IMPORTANT SAFETY INFORMATION 

This  section  contains  important  safety  information  for  the 

KISAE  Abso  DC  to  DC  Battery 

Charger

. Each time, before using the unit, READ ALL instructions and cautionary markings on or 

provided  with  the  unit,  and  all  appropriate  sections  of  this  guide.  The  unit  contains  no  user-
serviceable parts. See Warranty section for how to handle product issues. 

 

 

WARNING: Fire and/or Chemical Burn Hazard!  

  Do not cover or obstruct any air vent openings and/or install in a zero-clearance compartment.  

 
WARNING: Failure to follow these instructions can result in death or serious injury. Keep away 

from children!

 

  When working with electrical equipment or lead acid batteries, have someone nearby in case of an 

emergency. 

 

Study  and  follow  all  the  battery  manufacturer’s  specific  precautions  when  installing,  using  and 
servicing the battery connected to the charger.  

  Wear eye protection and gloves. 

  Avoid touching your eyes while using this unit. 

  Keep  fresh  water  and  soap  on  hand  in  the  event  battery  acid  comes  in  contact  with  eyes.  If  this 

occurs,  cleanse  right  away  with  soap  and  water  for  a  minimum  of  15  minutes  and  seek  medical 
attention. 

  Batteries produce explosive gases. 

DO NOT 

smoke or have an open spark or fire near the system. 

  Keep unit away from moist or damp areas. Never expose unit to snow, water etc. 

  Avoid dropping any metal tool or object on the battery. Doing so could create a spark or short circuit 

which goes through the battery or another electrical tool that may create an explosion. 

 
WARNING: Explosion hazard!

 

  Do  not  use  the  unit  in  the  vicinity  of  flammable  fumes  or  gases  (such  as  propane  tanks  or  large 

engines). 

  Avoid covering the ventilation openings. Always operate unit in an open area. 

  Prolonged contact to high heat or freezing temperatures will decrease the working life of the unit. 

  The 

DMT2430

 unit is designed for use on 

24V  House  Battery  System

 only. Do not use it on 12V 

House Battery System. 

 
CAUTION:

 

  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning use of the appliance by a person responsible for their safety. 

  Children should be supervised to ensure that they do not play with the appliance. 

  Do not charge non-rechargeable batteries because of the danger of eruption. 

  During charging, batteries should be placed in a ventilated area. 

  The battery terminal not connected to the chassis has to be connected first. 

  The  other  connection  is  to  be  made  to  the  chassis,  remote  from  the  battery  and  fuel  line.  The 

battery charger is then to be connected to the supply mains (household power). 

  After  charging,  disconnect  the  battery  charger  from  the  supply  mains.  Then  remove  the  chassis 

connection and then the battery connection. 

  Only allow children at least 8 years old to use the battery charger. Give sufficient instruction so that 

the child is able to use the battery charger in a safe way and explain that it is not a toy and must not 
be played with. 

  Examine  the  battery  charger  regularly  for  damage,  especially  the  cord,  plug  and  enclosure.  If  the 

battery charger is damaged, it must not be used until it has been repaired. 

 

Summary of Contents for DMT1230

























Reviews: