background image

1

UNVENTED (VENT-FREE)

FIREBOX 

Circulating Models

Listed Certified for USA

FVF300

FVFB300MVN, FVFB300MVP Burner Systems are approved to

ANZI Z21.11.2b – 1998, ANZI Z21.11.2 – 1996 for the FVF300 Vent Free Firebox only

Owner’s Operation 

and Installation Manual

Warning

If the information in this manual is not followed 
exactly, a fire or explosion my result causing property damage,
personal injury, or loss of life.

– Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer,

service agency, or the gas supplier.

Warning

Improper installation, adjustment, 
alteration, service, or maintenance
can cause injury or property 
damage. Refer to this manual for 
correct installation and operational
procedures. For assistance or
additional information consult a
qualified installer, service agency, or
the gas supplier.

Warning

The FVF300 Firebox is to be used
only with certain vent-free gas log
heaters (see table 1, Page 4).  Do not
burn wood or other materials in these
fireboxes.

Save this manual for future reference •

2340 Logan Ave., Winnipeg, MB, Canada, Phone: (204) 632-1962

Printed in Canada • PART #300FVF-MAN

Rev 08/01/04

Warning

This is an unvented gas-fired heater. It uses air (oxygen) from the

room in which installed. Provisions for adequate combustion and

ventilation must be provided. Refer to Page 11.

This appliance must be installed by a licensed plumber or

gas fitter in the Commonwealth of Massachusetts and meet

the requirements of 527 CMR 30 and 248 CMR.

Summary of Contents for FVF300

























Reviews: