Kingsman Fireplaces Marquis Bentley ZCV39LP Installation Instructions Manual Download | Manualshive

Page: 1 / 93

background image

Model Numbers: ZCV39N, ZCV39NE, ZCV39NE2, ZCV39LP, ZCV39LPE, ZCV39LPE2

ZCV42N, ZCV42NE, ZCV42NE2, ZCV42LP, ZCV42LPE, ZCV42LPE2

Certified to: ANSI Z21.88-2017 • CSA 2.33-2017,

CSA 2.17-2017

Vented Gas Fireplace Heaters

Model Numbers: ZCV39NH, ZCV39NHE, ZCV39NHE2, ZCV39LPH, ZCV39LPHE, ZCV39LPHE2

ZCV42NH, ZCV42NHE, ZCV42NHE2, ZCV42LPH, ZCV42LPHE, ZCV42LPHE2

Certified to: ANSI Z21.88-2017 • CSA 2.33-2017,

CSA 2.17-2017

Vented Gas Fireplace Heaters

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

-WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department

-Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

Installation Instructions

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA

only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified kit is used.

INSTALLER: Leave this manual with the

appliance.
CONSUMER: Retain this manual for

future reference.

A Division of R-Co. Inc.

2340 Logan Ave.

Winnipeg, Manitoba Canada

R2R 2V3 Ph.: (204) 632-1962

Printed in Canada January 22, 2020

Part# 39ZCV-MAN17

For Propane Horizontal

installations the venting must be

an additional one foot above the

minimum vertical rise off the flue

before going horizontal.

WARNING:

If the information in these instructions are not followed exactly, a fire or explosion may

result causing property damage, personal injury or loss of life.

BENTLEY

VENTED GAS FIREPLACE HEATER:

NOT FOR USE WITH SOLID FUEL.

1
2
3
...
»

Summary of Contents for Marquis Bentley ZCV39LP






























































































Reviews:

No comments

Related manuals for Marquis Bentley ZCV39LP

Brand: Cadet Pages: 13

Brand: Zibro Pages: 103

Brand: Napoleon Pages: 108

Brand: JAYLINE Pages: 10

Brand: Napoleon Pages: 56

Ontario APCL**RN

Brand: Formosa Pages: 44

Brand: Kingsman Pages: 43

Brand: Febo Pages: 16

Zermatt 10033051

Brand: Klarstein Pages: 44

FP-7-LM ANTOINETTE

Brand: Valcourt Pages: 2

MILLIVOLT DVCD FP3-4 Series

Brand: Empire Comfort Systems Pages: 96

Brand: MHSC Pages: 36

Brand: HEINZE Pages: 2

Crea7ionEVO PLUS 1200

Brand: GlammFire Pages: 52

Brand: Kennedy Pages: 24

Brand: MODENO Pages: 20

Brand: MODENO Pages: 20

Brand: Kingsman Fireplaces Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands