background image

Do install the circuit break. If not, it may cause malfunction. 

of at least 3mm in all poles should be connected in fixed 

wiring.

magnet buckle and heating buckle function, it can protect

the circuit-short and overload.

power supply circuit and circuit break.

Precautions

WARNING

note the following table.

 

Air switch should be included 

An all-pole disconnection switch having a contact separation 

Must follow the electric safety regulations when installing 

the unit.

grounding wire of power socket.

Properly connect the live wire, neutral wire and 

any work related to electricity and safety.

Be sure to cut off the power supply before proceeding 

Including an circuit break with suitable capacity, please 

Air Conditioner should be properly grounded. Incorrect 

Don't use unqualified power cord.

grounding may cause electric shock.

According to the local safety regulations, use qualified 

Installation must be performed by qualified professionals. 

Otherwise, it may cause personal injury or damage.

Attachment

3

Make sure the power supply matches with the requirement 

of air conditioner. Unstable power supply or incorrect wiring

may result in electric shock,

 

fire hazard or malfunction.

Please install proper power supply cables before using the

air conditioner.

Summary of Contents for KW09HQ3D6DI













































Reviews: