background image

Page 1

TABLE OF CONTENTS

  Section Contents 

Page

 

1. INTRODUCTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

 

2. 

DEFINITION OF TERMS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

 

3. INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

 

4. 

ANTENNA CONFIGURATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-25

 

5. OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

 

6. 

SECOND RECEIVER OPERATION FOR DISH AND BELL TV. . . . . . . . . . . . . . . . . 28-29

 

7. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

 

8. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

 

9. 

LIMITED WARRANTY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Bell TV is an official trademark of Bell Canada. 

DIRECTV is a registered trademark of DIRECTV, Inc. 

DISH is a registered trademark of DISH Network L.L.C.

HDMI is a registered trademark of HDMI Licensing L.L.C.

KING and KING Dome are trademarks of Electronic Controlled Systems, Inc.

IMPORTANT!

The TV market is expanding and changing.  The information in this manual was accurate at the time of 

printing.  If your KING Dome does not operate as outlined in this manual please call KING at (952) 922-6889 or 

visit our website at www.kingcontrols.com.  KING is not responsible for changes outside of its control.

The KING Dome is factory pre-set for DIRECTV

®

 standard digital programming broadcast from the 101° W 

satellite.  If you also receive your local channels from DIRECTV’s 119 satellite or if you subscribe to DISH

®

 or 

Bell TV™ programming, YOU MUST CONFIGURE THE ANTENNA to work with your satellite service.  Doing 

this will allow the KING Dome to lock on the correct satellites to receive your programming and also enable 

automatic satellite switching via the receiver’s remote control for multi-satellite service.  

Antenna configuration is a one time procedure that 

MUST BE COMPLETED before using your KING Dome 

antenna.  Configuration may be done with the supplied wall mount controller, or the 1844 Keypad 

(dealer tool).  See the antenna configuration section in this manual for specific instructions.

The KING Dome will not receive HD channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°.

Please read this entire manual before beginning the installation.

PRODUCT REGISTRATION

To provide on-going technical support and to better facilitate warranty processing,

please register your product at www.kingcontrols.com/products/productregistration/.

Summary of Contents for Dome 9704-LP





































Reviews: