background image

KING-METER TECHNOLOGY CO., LTD

 

No.15, Chenchang Road, Beichen Dist.Tianjin,300134,CN 

Fax

+0086 022 8478 0358 Tel: +0086 022 8478 

 

 

 

4. Installation Instruction 

Fix the display on the handlebar and adjust the viewing angle. When the e-bike is powered off, just   
plug the connector of the display and the corresponding connector of the controller to complete the   
installation. 

5. Operation Instruction 

5.1 Power ON/OFF 

After pressing the ON/OFF button shortly, the display starts to work and provides the controller   
working power. In the power-on state, short press the ON/OFF button to turn off the power of the   
electric vehicle. In the shutdown state, the meter no longer uses battery power, and the leakage   
current of the meter is less than 1uA.   
If the e-bike is not used for more than 10 minutes, the display will automatically shut down. 

5.2 RFID function 

5.2.1 Binding RFID card 

Swipe the main card in the prompt swiping interface, turn off the battery after the battery light flashes, 
and turn it on again to enter the card matching interface. After booting, it first prompts to match the 
main card. At this time, the fourth battery light is always on, and the third light flashes. At this time, the 
swiped card is regarded as the main card; then it prompts to match the secondary card 1, at this time the 
fourth The power light is always on, the third and second power lights are turned on in turn and then go 
out. Repeat the cycle before completing the secondary card 1 matching. At this time, the swiped card is 
recognized as secondary card 1; then it prompts to match secondary card 2. At this time, the fourth 
battery light is always on, and the remaining three battery lights turn on from high to low and then go out. 
Repeat the cycle before completing the secondary card 2 matching. At this time, the swiped card is 
recognized as secondary Card 2. After all three cards are configured, the battery indicator flashes and 
then shuts down. Power on again and enter the prompt swiping interface. At this time, the three cards 
have been updated to the newly equipped three cards. 

Summary of Contents for 790-R LED











Reviews: