King Industrial Excelsior Duo-Fence XL-U30 Instruction Manual Download Page 4

INSTALLING FRONT RAIL AND TUbE ASSEMbLY

Place and align the mounting holes of the front rail and tube assem-

bly (A) Fig.1 with the holes in the front lip of the table (C) and exten-

sion wings (D & E). Install the front rail and tube assembly to the

table and extension wings using 4 countersunk head bolts, 4 wash-

ers, 4 spring washers and 4 hex. nuts. 

Before securing it in place, adjust it up or down to ensure the front

rail edge is set at 1/8” below the lowest edge of the miter gauge

T-slot. Once adjusted, tighten all 4 countersunk head bolts. 

INSTALLING REAR RAIL

Place and align the mounting holes of the rear rail (B) Fig.1 with the

holes in the rear lip of the table (C) and extension wings (D & E).

Install the rear rail to the table using 2 cap screws, washers, and

spring washers. 

Then use 2 cap screws, 4 washers, 2 spring washers and 2 hex.

nuts to fix the rear rail to the  extension wings. Before securing it in

place, adjust it up or down to ensure the rear rail edge is set flush

with  the  lowest  edge  of  the  miter  gauge  T-slot  (to  allow  free

movement of the miter gauge). Once adjusted, tighten all 4 cap

screws. 

ADJUSTING RIP FENCE

The rip fence must be perfectly aligned with the table T-slot. To verify this, place rip

fence on table and align the edge of the rip fence with the table T-slot, lower the 

locking lever (A) Fig.2 to lock it into place. Check to see if the edge of the rip fence

and the table T-slot are parallel. If they are not parallel, unlock the rip fence and turn

it upside down as shown in Fig.3. Adjust the set screws (A) Fig.3 in or out, verify your

adjustment, repeat if necessary.

The lock lever pressure can be adjusted by loosening the front lock nuts (B) Fig.2

and adjusting the set screws (C) the same amount. Make sure the fence remains 

parallel with the table T-slot. If you turn a set screw one full turn, it is necessary to 

adjust the other set screw one full turn. Retighten lock nuts. 

To set the fence perpendicular to the table, place a square on the table and against

the side of the fence, loosen the top lock nuts (D) and adjust the set screws (E) until

the fence is perpendicular. Retighten lock nuts. 

The pointer window (F) Fig.2 position can be adjusted if needed, loosen round head

allen screws (G), reposition the pointer window and retighten round head allen screws.

FIGURE 1

FIGURE 2

FIGURE 3

ASSEMbLY AND ADJUSTMENTS

Summary of Contents for Excelsior Duo-Fence XL-U30







Reviews: