King-Gage ES2 550*-1 Series Installation And Operation Instructions Manual Download Page 2

Page 2

ES2 Electronic Liquid Level Transmitter

EX-1832

© 2004 King Engineering Corporation. All rights reserved.

The information contained in this manual was accurate at
the time of release. Specifications are subject to change
without notice.

Warranty

 - All King Engineering products are guaranteed

to be free from defects in material and workmanship for
one year from the date of purchase. Any product or part
found to be defective under normal use within one year of
purchase will be repaired or replaced at no charge if
returned to the company at Ann Arbor, Michigan within
ten days of discovery of the defect. No other warranties,
whether expressed, implied or statutory, including the
warranties of fitness for a particular purpose or merchanta-
bility, are given by this agreement.
The exclusive remedy for nonconformity of these goods
shall be repair and/or replacement of the nonconforming
goods or parts.

Seller will not be liable for consequential damages resulting
from breach of this agreement. The term “consequential
damages” shall include but shall not be limited to damage
to all machines, equipment and goods other than the
goods sold hereby, interruption of production, loss of
profits, delays of any kind, administrative expense, and
overhead.

Revisions:

(A) August, 2004 - Original Release

Summary of Contents for ES2 550*-1 Series









Reviews: