King-Dome 9754-LP Installation And Operating Instructions Manual Download Page 23 | Manualshive

Page: 23 / 40

background image

Page 21

BELL EXPRESSVU ANTENNA CONFIGURATION

Standard Digital (satellite 91)

1. On the King-Dome controller, press and release the

ON/SEARCH button. Wait for the status light to flash
orange, and then

WAIT 4 MORE SECONDS

.

2. Press and release the ON/SEARCH button

8

times.

The status light starts rapidly flashing green and red.

3. Press and hold the TRACK button for 4 seconds.

The status light will turn orange for 1 second,
and then start flashing green or red.

4. Press OFF.

5. After you have successfully configured the antenna, you must configure

your receiver for mobile use. To configure your receiver,

GO TO PAGE 26 AND RUN THE CHECK SWITCH.

HDTV (satellites 82, 91)

1. On the King-Dome controller, press and release the

ON/SEARCH button. Wait for the status light to flash
orange, and then

WAIT 4 MORE SECONDS

.

2. Press and release the ON/SEARCH button

36

times.

The status light starts rapidly flashing green and red.

3. Press and hold the TRACK button for 4 seconds.

The status light will turn orange for 1 second,
and then start flashing green or red.

4. Press OFF.

5. After you have successfully configured the antenna, you must configure

your receiver for mobile use. To configure your receiver,

GO TO PAGE 26 AND RUN THE CHECK SWITCH.

«
...
21
22
23
24
25
...
»

Summary of Contents for 9754-LP









































Reviews:

No comments

Related manuals for 9754-LP

Brand: M2 Antenna Systems Pages: 12

Movin' View MV-0500

Brand: Winegard Pages: 12

Brand: DX Engineering Pages: 32

Brand: Federal Signal Corporation Pages: 18

Brand: ICC Pages: 17

Brand: Maco Antennas Pages: 9

Brand: Maco Antennas Pages: 9

Brand: RCA Pages: 2

Brand: M2 Pages: 4

Brand: CommScope Pages: 8

Brand: Cabletech Pages: 20

Brand: King Controls Pages: 5

Brand: Teltonika Pages: 40

Extreme Wireless

Brand: Extreme Networks Pages: 147

Brand: Hy-Gain Pages: 8

Brand: Hy-Gain Pages: 32

Type 123 1.2 Meter Class I and II Antenna System

Brand: Skyware Pages: 18

RDL-3000 Series

Brand: Redline Communications Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands