ELECTRICAL INFORMATION
WARNING
ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS
INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE BAND SAW DISCONNECTED FROM THE POWER SOURCE.
FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!
POWER SUPPLY
WARNING:
YOUR BANDSAW IS WIRED AT THE FACTORY FOR 110-120V
OPERATION, IT MUST BE CONNECTED TO A 110-120V/15-AMP. TIME DELAY
FUSE OR CIRCUIT BREAKER. FAILURE TO CONNECT IN THIS WAY CAN
RESULT IN INJURY FROM SHOCK OR FIRE. This bandsaw is intended for use on
a electrical circuit that has an outlet and a plug which looks like the one illustrated
in Fig.1.
WARNING:
DO NOT USE A TWO-PRONG ADAPTOR FOR THEY ARE NOT IN
ACCORDANCE WITH LOCAL CODES AND ORDINANCES. NEVER USE IN
CANADA.
GROUNDING
This bandsaw must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current, to
reduce the risk of electric shock. This bandsaw is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not
modify the plug provided, if it will not fit the outlet, have the proper outlet installed by a qualified electrician. Not all outlets are properly
grounded. If you are not sure if your outlet is properly grounded, have it checked by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer
surface that is green with or without yellow stripes is the equipment-grounding condustor. If repair or replacement of the power cord or plug is
necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether
the tool is properly grounded. Use only 3 wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the tool’s
plug. Repair or replace damaged or worn cord immediately.
WARNING:
IF NOT PROPERLY GROUNDED, THIS BAND SAW CAN CAUSE ELECTRICAL SHOCK,
PARTICULARLY WHEN USED IN DAMP LOCATIONS. TO AVOID SHOCK OR FIRE, IF THE POWER
CORD IS WORN OR DAMAGED IN ANY WAY, HAVE IT REPLACED IMMEDIATELY.
USE PROPER EXTENSION CORD
Make sure the extension cord is in good condition. When using an extension cord, be sure to use one
heavy enough to carry the current your tool will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. See Fig.2 for table showing correct size to use
depending on the cord lenght and the nameplate amperage rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord. Always use U.L. and CSA listed extension
cords.
WARNING:
Replace damaged cords immediately. Use of damaged cords can shock, burn or
electrocute.
ON/OFF SWITCH WITH REMOVABLE SAFETY KEY
The On/Off switch (A) Fig.3 comes with a removable safety key (B). When the safety key is removed
(when switch is in Off position only) from the switch and placed in a safe location, unauthorized persons
or children can’t turn the switch to the On position, restricting use. It is recommended to always remove
the safety key from the switch whenever the bandsaw is not in use.
FIGURE 2
Tool’s
Amperage
Rating
3-6
6-8
8-10
10-12
12-16
Cord Size in A.W.G.
Cord Length in Feet
25
50
100 150
18
16
16
14
18
16
14
12
18
16
14
12
18
16
14
12
14
12
-
-
FIGURE 1
GROUNDED OUTLET
CURRENT
CARRYING
PRONGS
GROUNDING PRONG
FIGURE 3
