background image

Technical Specifications 

Model ..........................................................................................................KC-4001LED 
Voltage-Cycle/Phase ......................................................................120V, 60Hz, 1 phase 
Amperage ................................................................................................................0.33A 
Lumens ......................................................................................................4,000 (6500K) 
Wattage ....................................................................................................................36W 
LED life ......................................................................................................+30,000 hours 

 
POWER SUPPLY 
WARNING:

 YOUR LED WORK LIGHT MUST BE 

CONNECTED TO A 120V, 15-AMP, BRANCH 
CIRCUIT BREAKER. FAILURE TO CONNECT IN 
THIS WAY CAN RESULT IN INJURY FROM 
SHOCK OR FIRE. 
 

GROUNDING 

Your work light must be properly grounded. Not all 
outlets are properly grounded. If you are not sure 
if your outlet is properly grounded, have it 
checked by a qualified electrician. If this work light 
should malfunction or breakdown, grounding    
provides a path of least resistance for electric    
current, to reduce the risk of electric shock. This work light is equipped with a cord having 
an equipment-grounding conductor and grounding plug. The plug must be plugged into an 
appropriate outlet that is properly installed and grounded in accordance with all local codes 
and ordinances. 
 

WARNING:

 IF NOT PROPERLY GROUNDED, THIS WORK LIGHT CAN CAUSE    

ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP LOCATIONS. TO AVOID 
SHOCK OR FIRE, IF THE POWER CORD IS WORN OR DAMAGED IN ANY WAY, HAVE 
IT REPLACED IMMEDIATELY. 

 
WARNING: 

TO MAINTAIN PROPER GROUNDING, DO NOT REMOVE OR ALTER THE 

GROUNDING PRONG IN ANY MANNER. 
 

120V OPERATION 

As received from the factory, your 
work light is ready to run for 120V 
operation. This work light is 
intended for use on a circuit that 
has an outlet and a plug which 
looks like the one illustrated in 
Fig.1. 

         

EXTENSION CORDS 

The use of any extension cord 
will cause some loss of power. Use the chart in Fig.2 to determine the recommended     
minimum wire size (A.W.G-American Wire Gauge) extension cord. Use only 3-wire    
extension cords which have 3-prong grounding type plugs and 3-hole receptacles which 
accept the tool’s plug. For circuits that are further away from the electrical circuit box, the 
wire size must be increased proportionately in order to deliver ample voltage. Refer to 
Fig.2 for wire length and size.

ELECTRICAL INFORMATION 

LENGTH OF 
EXTENSION 

 

0-25 FEET 

26-50 FEET 

51-100 FEET 

WIRE SIZES REQUIRED 
(AMERICAN WIRE GAUGE) 

120V LINES 

NO.16 
NO.14 
NO.12

FIGURE 2

FIGURE 1

PROPERLY GROUNDED OUTLET

CURRENT  
CARRYING PRONGS

GROUNDING PRONG

Summary of Contents for KC-4001LED








Reviews: