background image

Technical Specifications

Model ......................................................................................................KC-2202LED-C

Voltage/Capacity ....................................................................................7.4V, 4,400 mAh

Battery type ....................................................................................................Lithium-ion

Lumens ....................................................................................................................2,200

Wattage ....................................................................................................................20W

Chargers........................................................................................................120V & 12V

Charge time ..........................................................................................................5 hours

LED life ......................................................................................................+30,000 hours

WARNING

: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into

this product, but must be supplied by the operator.

WARNING: 

Get to know your LED work light. Do not use until you have read and

understood this instruction manual. Only use the supplied King chargers to charge the

7.4V Lithium-ion battery. 

Battery and Charger Safety Precautions

1) Never attempt to open the battery

for any reason. If battery housing has cracked,

discontinue use immediately and do not try to recharge it. 

2) Never charge a wet LED work light

or if battery shows signs of corrosion.

3) Do not use an extension cord

with the charger, plug charger directly into a 120V AC

receptacle.

4) Do not use charger

if power cord is damaged, replace damaged cord or charger.

5) Do not charge battery

when work area or the temperature is below 0

0

C or above

45

0

C.

6) Unplug charger

when not in use.

7) The contents of the battery is slightly acidic

, do not incinerate the battery, it can

explode in a fire.

8) A small leakage from the battery

may occur under extreme usage, charging or

temperature conditions. This does not indicate a battery failure. However, if the battery

housing is cracked and leakage gets on your skin, follow these steps:

-Wash with soap immediately.

-Neutralize area with mild acid such as vinegar or lemon juice.

-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes,

then seek medical attention.

Lithium-ion Battery

Lithium-ion batteries do not have a memory and do not require to be completely

discharged periodically. After use, charge battery so that it is fully charged for the next

time you use this tool. A fully charged battery will only loose about 2% of its charge per

month during storage.

LITHIUM BATTERY AND CHARGING 

INFORMATION

Summary of Contents for KC-2202LED-C








Reviews: