background image

SETTING THE BLADE SQUARE WITH THE TABLE

1. Make sure that the electrical plug is removed from the main power supply.
2. Push the saw head down to its lowest position, then pull and turn the head release knob

to hold the saw head in the transport position.

3. Loosen the miter lock handle.
4. Rotate the table until the pointer is positioned at 0

0

.

5. Retighten the miter lock handle.
6. Loosen the bevel lock knob at the rear of the machine and set the saw arm at 0

0

bevel (the

blade at 90

0

to the miter table). Tighten the bevel lock knob.

7. Place a square (A) Fig.11 against the table and the flat part of the blade body.

NOTE:

Make sure that the square contacts the flat part of the saw blade body, not the teeth.

8. Rotate the blade by hand and check the blade-to-table alignment at several points.
9. The edge of the square and the saw blade should be parrallel.

10. If the saw blade angles away from the square, adjust as follows;
11. Make sure the positive stop adjustment knob (A) Fig.12 is pushed in all the way and the

bevel lock knob (B) is fully tightened. Loosen the two hex. screws (C & D) inside the pivot
bracket using a hex. key.

12. Loosen bevel lock knob (B) and adjust the head of the saw in or out to bring the saw blade

into alignment with the square.

13. Once perfectly aligned, retighten the bevel lock knob (B) and the two hex. screws (C & D)

inside the pivot bracket. Recheck the alignment.

14. Readjust bevel pointer (B) Fig.11 to line up with the 0º on the bevel scale.

ADJUSTING THE 45

0

STOP BOLTS

After setting the blade square with the table, the left and right side 45

0

stop bolts will need to

be adjusted.

1. Loosen the hex. nut and cap screw (F) Fig.12.
2. Tilt the head completely to the left side.
3. Place a 45

0

combination square against the table and the flat part of the blade body. 

4. Once the head is at a perfect 45

0

angle, tighten bevel lock knob (B), then tighten the cap

screw (F) against the bevel lock knob (B) shaft and tighten hex. nut (F).

5. Repeat the above steps for the right side 45

0

stop bolt using the hex. nut and cap screw

(E).

SETTING THE FENCE SQUARE WITH THE BLADE

1. Make sure that the electrical plug is removed from the main power supply.
2. Push the saw head down to its lowest position, then pull and turn the head release knob

to hold the saw head in the transport position.

3. Loosen the miter lock handle.
4. Rotate the table until the pointer is positioned at 0

0

.

5. Retighten the miter lock handle.
6. Loosen the bevel lock knob at the rear of the machine and set the saw arm at 0

0

bevel (the

blade at 90

0

to the miter table). Tighten the bevel lock knob.

7. Place a square (A) Fig.13 against the fence (B) and the flat part of the blade.

NOTE:

Make sure that the square contacts the flat part of the saw blade, not the teeth.

8. The edge of the square and the fence should be parrallel.

9. If the fence angles away from the square, adjust as follows;
10. Remove the fence extension cap screws, loosen the rear fence extension lock knobs and

remove fence extensions by sliding them off the fence. Loosen the now exposed fence cap
screws (C) Fig.13 on both sides and position the fence (B) against the square and
retighten all cap screws.

11. Reinstall fence extensions.

Figure 11

Figure 13

Figure 12

ADJUSTMENTS

Summary of Contents for 8385N













Reviews: