Changing Nose Pieces
1. Select the Nose Piece (1,2,3,4) you require for the job at hand.
2. Using the supplied Wrench (9), remove the attached Nose Piece (1,2,3,4) using the open end part of the Wrench (9), by rotating anti-clockwise.
3. Once loose, remove the Nose Piece (1,2,3,4) that is fitted to the tool.
4. Select the Nose Piece (1,2,3,4) you require to suit the rivet being used, (which are stored in the Wrench (9) handle), by rotating the Nose Piece (1,2,3,4) anti-clockwise from the Wrench (9).
5. Insert the desired Nose Piece (1,2,3,4) into the threaded area of the Nose Housing (5) and tighten using the Wrench (9) by rotating clockwise.
6. The KP45001 EZI-RIV Drill Attachment is now ready to use!
Operation
1. Align and insert the 6.35mm (1/4”) Hex Shank (6) of the EZI-RIV Drill attachment, into the Chuck of your drill and tighten the drill chuck (Fig 1).
2. While holding the drill attachment Body housing (7), put the drill in reverse and pull the drill trigger until you hear a clicking sound (Fig 2).
3. Ensure you have the correct Nose Piece (1,2,3,4) installed to suit the rivets being used for the job at hand.
4. Insert the desired rivet shaft into the Nose Piece (1,2,3,4) (Fig 4).
5. With the desired rivet inserted into Nose Piece (1,2,3,4), align and insert the rivet into your pre-drilled material.
Caution: Ensure the correct drill speed is selected to ensure the speed is a Max of 1000 RPM.
6. While holding the drill attachment Body Housing (7) in one hand, select the forward direction of the drill & pull the drill trigger to clench the rivet to the material. (during this process the rivet
shaft will snap off from the Rivet head) (Fig 5).
7. Select reverse on the drill and pull the drill trigger until a clicking sound can be heard, this will allow the rivet shaft to be expelled from the drill attachment (Fig 6).
Repair
1. Have your KP45001 EZI-RIV Drill Attachment serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety, reliability and performance of the
KP45001 EZI-RIV Drill Attachment is maintained.
Maintenance
1. Clean and lubricate the jaws periodically, at least every 1,000 Rivets. Lubricate the riveter jaws as needed with a lubricant such as INOX or TF2 lubricating spray (not supplied).
Office Contact Details
Phone: 1300 657 528
Fax: 1300 556 005
Email: [email protected]
Website: www.kincrome.com.au
Warranty given by Kincrome Tools & Equipment Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria, Australia (Tel +61
3 9730 7100) If this product has materials or workmanship defects (other than defects caused by abnormal or non warranted use)
you can, at your cost, send the product to place of purchase, an authorised Kincrome service agent or one of Kincromes addresses
for repair or replacement. Your rights under this warranty are in addition to any other rights you have under the Australian, United
Kingdom & Ireland Consumer Law or other applicable laws. Our goods come with guarantees that cannot be excluded under
the Australian, United Kingdom & Ireland Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For further details please visit www.
kincrome.com.au or call us. Due to minor changes in design or manufacture, the product you purchase may sometimes differ from
the one shown on the packaging.
SCAN FOR
INSTRUCTIONAL
VIDEO
(Fig 1)
(Fig 2)
(Fig 3)
(Fig 4)
(Fig 5)
(Fig 6)
PART NO.
DESCRIPTION
PART NO.
DESCRIPTION
KP45001-4
KP45001 Jaws (Set 2 Piece)
KP45001-17 KP45001 Rear CirClip
KP45001-6
KP45001 Spring
KP45001-18 KP45001 3.2mm Nose Piece
KP45001-7
KP45001 Nose Housing
KP45001-19 KP45001 2.4mm Nose Piece
KP45001-8
KP45001 4.00mm Nose Piece
KP45001-20 KP45001 4.8mm Nose Piece
KP45001-13
KP45001 Internal E-Clip
* For a full list of available spare parts for this item, visit the Kincrome website www.kincrome.com.au or alternatively
contact Kincrome Customer Service.
* Kincrome reserve the right to change spare parts at any time without notice.
MONTH
WARRANTY
12
Spare Parts
