SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
SD-Card:Data__Select__
<0:Selection_disbld
SD-Card:Data__Read____
<NORMAL_OPERATION>
SD-Card:Data__Select__
<3:VsC_Type_______
SD-Card:Data__Read___
<32:Recip_Semihrmtc
SD-Card:Data__Select__
<4:VsC_Cylinders__
SD-Card:Data__Read___
<42:2 cylinders____
SD-Card:Data__Select__
<5:Supply_Voltage__
SD-Card:Data__Read____
<53:50_Hz_400_V____
OPERATION___________
REFRIGERATION SETUP_
COMPRESSOR SETUP _
SPECIAL ADJUSTMENTS_
Ensure that all recommendations for compliance to mounting, electrical safety, EMC and UL regulations have
been adhered to.
1.1 Pressure transmitters
Warning:
Only use approved pressure transmitters!
This refrigeration application is preset for use with the following
Huba Control
pressure transducers:
1. Basic information on first set-up
Low Pressure pe: -0.5 … 7.0 bar
A REFR-P-TRANSD-LP7N+PL
High Pressure pc: 0 … 30 bar
A REFR-P-TRANSD-HP30N+PL
For alternative pressure transmitters and pressure ranges refer to Parameter SP0, p. 6 of Planning Guide.
1.2 Recommendations
•
It is important to ensure that an interlocked contactor is fitted between the Refrigeration Inverter and the
compressor if a parallel bypass connection is used.
•
In particular ensure that two isolated contacts of a relay are connected to the Safe-Torque-Off inputs of
F
rigo
P
ack
®
FU+
Refrigeration Inverter: STO-A (Terminal X10:1) / STO-B (Terminal X10.3).
• Remove start command (cable to terminal X13:2)
• Connect main power supply
• Verify that the blue LED for suction pressure lights on module BM-1. If not, then check if the wiring of the
pressure transmitter is correct.
• If a discharge pressure transmitter is used, then verify that the red LED lights on module BM-1. If not, then
check if the wiring of the pressure transmitter is correct.
• Measure the pressures with a refrigeration pressure gauge. Verify that the pressures indicated in menu
OPERATION at parameter 03: pe_RACK_pc agree with these external measurements.
1.3 Keypad functionality
1.4 Menus - Selection of user level for first set-up
To start commissioning, the user level TECHNICIAN must be enabled. The steps shown below have to be
followed. Press key "Back" several times to access the menu "View Level".
Password for user level TECHNICIAN:
8670
. The level is then activated for 10 minutes.
OK
OK
OK
OK
OK
PASSWORD:
8670
Back
Back
Start screen
Menu levels
Key "Back"
● Navigates to previous level
● Press multiple times to enter Operator Menu
● Aborts the edit mode
Key "OK"
● Displays the next menu level
● Changes to parameter entry mode
● Accepts value entered
"Green" key
Green light on
● Compressor running
● When flashing with "Red" key: Frequency Inverter
in Configuration Mode
Key "Red"
● Resets any trip
Red light on
● Compressor stopped
● When flashing with "Green" key: Frequency Inverter
in Configuration Mode
Keys "Left" and "Right"
● Displays previous menu level
● Selects the digit to be changed
● Selects next/previous set of parameters, compressors, etc.
Keys "Up" and "Down"
● Moves up or down through selected menu level
● Increments / decrements the value of the displayed
parameter by "1"
User level
- 2 -
www.frigokimo.com
FS 1.7
