Kikusui PMX32-3DU, User Manual

Page: 42 / 104

42
User’s Manual
PMX_MULTI
Basic Functions
CONFIG Settings
Use the CONFIG settings to perform system configuration of the product. You can set and display the fol-
lowing parameters in the CONFIG settings.
Effect:
●
indicates that the parameter is affected when the panel settings are reset (CF00).
■
indicates that the parameter may be affected when the LAN interface settings are reset (CF40:
LCI
/
DEF / APPL ).
Note: “A” indicates that the parameter is applied when the PMX exits from CONFIG settings.
“B” indicates that the parameter is applied when the power is turned on. “C” indicates that the parameter
is applied after CF40 is executed.
Display
switching Parameter
number Mnemonic Setting/ display Effect Note
System CF00 − Reset Panel setting reset − A
CF01 PON Power on Output state at power-on − B
CF02 MEM Memory Memory content display − A
CF03 LOC Lock Key lock content − A
CF04
*1
E.OUT Ext. on/ off External control for turning output on/off ● A
CF05
*1
E.LOG Ext. logic External control logic for turning output on/off − A
CF06
*1
PRIO Priority Output-on startup state − A
CF07
*1
RIS.T Rise Time Rise time when a value is changed − A
CF08 A.OFF Alarm off Output state when a protection function (OVP/OCP) is
activated − A
CF09
*1
DTRC Dual tracking Tracking operation − A
Interface CF20 LAN LAN LAN interface
■
*2 B
CF21 USB USB USB interface − B
CF22 232 RS232C RS232C interface − B
CF23 TRAC Trace SCPI communication error display − A
CF24 WDOG Watchdog Communication monitoring (watchdog) timer − A
CF25 BEEP Beep Buzzer on/off − A
LAN
*3 CF30 IP1 Ip addr. 1 IP address display (1) − −
CF31 IP2 Ip addr. 2 IP address display (2) − −
CF32 IP3 Ip addr. 3 IP address display (3) − −
CF33 IP4 Ip addr. 4 IP address display (4) − −
CF34 HA1 HW. addr. 1, 2 MAC address display (1) and (2) − −
CF35 HA2 HW. addr. 3, 4 MAC address display (3) and (4) − −
CF36 HA3 HW. addr. 5, 6 MAC address display (5) and (6) − −
CF40 BOOT LAN Reboot LAN setting reset (LCI/DEF)/apply (APPL) − A
CF41 ADR Address config IP address assignment method
■
B/C
CF42 S.IP1 Static IP 1 Manual IP address setting (1)
■
B/C
CF43 S.IP2 Static IP 2 Manual IP address setting (2)
■
B/C
CF44 S.IP3 Static IP 3 Manual IP address setting (3)
■
B/C
CF45 S.IP4 Static IP 4 Manual IP address setting (4)
■
B/C
CF46 SUB Subnet Mask IP address subnet mask ■ B/C
USB
CF50
*4 VID V. ID Vendor ID (VID) display − −
PID P. ID Product ID (PID) display − −
RS232C CF51 BAUD Baud rate RS232C baud rate − B
Firmware
CF60
*5
VER Version Firmware version display − −
B.NO Bild no. Build number display − −
*1. Can be set separately for each channel
*2. This parameter is affected only when the LAN interface settings are reset (CF40: LCI / DEF / APPL ).
*3. For details on the LAN interface settings, see the “Communication Interface Manual” on the included CD-ROM.
*4. The vendor ID is shown in CH1 and the product ID in CH2.
*5. The firmware version is shown in CH1 and the build number in CH2.