Kikusui PCZ1000A Operation Manual Download Page 39 | Manualshive

Page: 39 / 100

Kikusui PCZ1000A Operation Manual Download Page 39

PCZ1000A

3-5

3

Ope

ration

3.2

Turning On the Power

This section describes the procedure for turning on the power. No load current will
flow if the PCZ1000A is turned on with its factory default settings. To allow a load
current to flow, the PCZ1000A needs to be set to load-on mode.

• Allow at least five seconds between turning the POWER switch on or off.

In-rush current of up to 80 A can occur at power on. Turning the POWER

switch on and off repeatedly during a short interval can result in the blown

input fuse.

Turning on the POWER switch

1

Check that the POWER switch is OFF ( ).

page 2-8 , 2-13

2

Check that all wiring connections are properly connected.

3

Turn the POWER switch to ON ( ).

4

Check the firmware version on the front panel display.

The front panel display shows the model name and firmware version.

The front panel display changes after approximately 2 seconds.

The upper part indicates the RMS current (Ar), peak current (Ap), and RMS voltage
(V)  supplied  to  the  load  terminals  of  the  PCZ1000A.  The  lower  part  shows  the
operation mode (the above example shows "I SET" which indicates constant current
mode) and the setting (0.00 A in the above example).

When the POWER switch is turned on for the first time after purchase, the
PCZ1000A will start up in its factory default state.

■

When an error occurs

In case the calibration data is changed to the abnormal value caused by deterioration
of  the  internal  memory  and  the  like,  "xx  xxx  EPPDATA  ERR"  ("x"  may  varies
depends on the contents of the error) is displayed with the buzzer sounds when the
POWER switch is turned on . It will return to the normal display in three seconds,
however,  the  error  for  the  setting  value  and  the  ammeter/voltmeter  may  become
large because of the calibration data is not properly confirmed.

• If the PCZ1000A is used while the error is occurred, it causes the failure.

Contact your Kikusui distributor/agent for repairs.

See

CAUTION

See

PCZ1000A
Ver. 1.00

0.00Ar 0.0Ap 0.0V
-- ISET 0.00A --

See

CAUTION

«
...
37
38
39
40
41
...
»

Summary of Contents for PCZ1000A





































































































Reviews:

No comments