Kikusui PCZ1000A Operation Manual Download Page 33 | Manualshive

Page: 33 / 100

Kikusui PCZ1000A Operation Manual Download Page 33

PCZ1000A

2-13

2

Unpacking and Installation

2.7.2

Connection to the Load Input Terminals

■

Load input terminals cover

This cover is fitted using the hole on the right side of the terminal cover when the
PCZ1000A is shipped from the factory to prevent the load input terminals from

being exposed.
Please attach the cover as shown in Fig.2-10 when not using the load input terminal
block. The load input terminals can be covered by using the hole on the right and
sliding the terminal cover to the left.

Fig.2-10 Load Input Terminals Cover

• Risk of electric shock. Never touch the load input terminals when

they are live.

Also, always use the load input terminals cover.

Risk of damage.
• Never connect the load input terminals to the equipment under test while

the PCZ1000A is in the load-on state.

• Never connect the load input terminals to the AC power line directly.

1

Turn off the POWER switch.

2

Remove the terminal cover from the load input terminal block.

3

Attach crimped terminals to the load wiring.

Use proper crimped terminals that suit the terminal screw size (M4).

4

Securely connect the load wiring to the load input terminals.

If the equipment under test has a ground terminal (GND), always connect this to the G

terminal on the load input terminal block of the

PCZ1000A

.

5

Attach the terminal cover removed in Step 2 using the hole provided on
the right of the terminal cover as shown in Fig.2-11.

Use the hole on the right to attach the terminal cover.

WARNING

CAUTION

«
...
31
32
33
34
35
...
»

Summary of Contents for PCZ1000A





































































































Reviews:

No comments