manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 15

BIM1000 Series

User’s Manual

15

Measurement

Measurement and Judgment Settings

You can configure the following measurement and judgment settings.

Sampling speed (SAMPLE)

Select the measurement speed. Slower the sampling speed the better the measurement accuracy. The 
measurement time varies depending on the Power supply frequency (Line Freq)

 (p. 37)

.

1

Press MEASURE.

2

Press SAMPLE (F1) to select the value.

The value switches each time you press the key.

This completes the setting.

Setup

Description

See

Sampling speed (SAMPLE)

Measurement speed.

p.15 

Average function (AVERAGE)

Number of measurements for calculating averages.

p.16 

Resistance Measurement range (RANGE)

Resistance measurement range.

p.17 

Resistance Upper judgment limit (UPPER)

“UP” is displayed when a value greater than or equal to 
the upper judgment limit is measured.

Resistance Lower judgment limit (LOWER)

“LOW” is displayed when a value less than or equal to 
the lower judgment limit is measured.

Resistance Unit (Ω/mΩ)

Unit of the resistance’s upper judgment limit and lower 
judgment limit.

Voltage Measurement range (RANGE)

Voltage measurement range.

p.18 

Voltage Upper judgment limit (UPPER)

“UP” is displayed when a value greater than or equal to 
the upper judgment limit is measured.

Voltage Lower judgment limit (LOWER)

“LOW” is displayed when a value less than or equal to 
the lower judgment limit is measured.

Value

Measurement time
Frequency 50 Hz

Frequency 60 Hz

FAST

20 ms

20 ms

MEDIUM

50 ms

42 ms

SLOW

160 ms

150 ms

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands