background image

Technical data sheet  1.10-51.110-81-en

 

DDC110-L1 .. DDC110-L4 technolon

®

 Room Module

 

D e v i ce   De s c ri p ti on

 

 
 

Notes on the device description

 

The description contains references for the deployment and assembly of the technolon

®

 

Room Module. 

In case of questions which cannot be clarified with this device description, please refer to the supplier or 
manufacturer for further information. 
 
The indicated installation instructions/regulations are valid in the Federal Republic of Germany. 
When using the I/O components in other countries, the builder or operator of the plant is responsible for 
compliance with the respective national regulations. 
 
The operating staff is to be instructed in accordance with the description of the technical data sheet. 

 
 

Safety Instructions

 

The currently valid worker’s occupational health regulations and regulations for the prevention of industrial 
accidents must be observed when assembling and using the devices. 
 
Any work concerning the installation or initial operation of the control devices shall be exclusively carried out by 
qualified specialists, see section “Qualified specialists”. 
 
Every person using the devices shall have read and understood the descriptions in the technical data sheet. 
 
If the equipment is not used according to the technical data sheet, the protection might be lower as stated. 
 
Meaning of the symbols in the technical data sheet: 

 
 

 

Warning of dangerous electrical voltage 

 

Danger 

 

 

 

 

General warning, strictly observe this notice

 

Warning 

 

 

 

 

Further notice to observe 

Note 

 

 

 

Danger

 

means mortal danger, severe bodily injuries or serious material damage in case of 
non-observance. 

Warning 

means danger of bodily injuries or material damage in case of non-observance. 

Note 

indicates information which is particularly emphasized. 

 
 

Qualified specialists

 

Qualified specialists for the purposes set out in this technical data sheet are persons who are familiar with the described 
devices and possess a qualification for their respective occupation. 
These are for instance: 

  Authorization to connect the devices according to the VDE rules and local Electricity Board regulations, as 

well as the authorization to switch the devices on and off taking the in-house regulations into account. 

  Knowledge of the regulations for the prevention of industrial accidents. 

  Knowledge of the utilization of the devices within the plant system.

 

 etc. 

 

 

Page 2 / 12 

Summary of Contents for Technolon DDC110-L1













Reviews: