background image

A

Page 5 / 32

Datasheet 1.10-65.040-01-EN

RPW414P-FTL

Product Description

Issue 2017-04-10

Item

Technical Data

RPW414P-FTL Room control module with room humidity/temperature sensor, SolarRadio technol-

ogy and integrated bidirectional EnOcean wireless interface.
Automatic determination of the utilization time profile/heating profile in the room for 
automatic control of comfort mode and economy mode.
For self-learning, energy self-sufficient and occupation-dependent control of the 
room temperature in conjunction with MD15-FTL wireless small actuator.

Nominal voltage

Dual power supply consisting of a solar cell and an internal energy stor-
age unit with priority management
Additional internal energy source 2x 3.6 V, AA lithium

Measured quantity

Room temperature and relative humidity in homes and offices

Measuring system

Temperature sensor:
Occupancy sensor:
Humidity sensor:

- Integrated digital measuring transducer
- Integrated PIR (“Passive infrared”) sensor
- Integrated digital measuring transducer

Measuring range

Temperature:
Relative air humidity:

0..50 °C
20..80%

Measuring tolerance

Temperature:
Relative air humidity:

Typically ±0.3 K
Typically ±3.0%

Display

LCD display:

Room temperature, room humidity, date or time, as required

Status indicators

Controls

Occupancy button: manually switch between comfort mode/

economy mode

Up arrow button: increase value

Down arrow button: reduce value

Selector button: select the menus or displays

Interfaces

EnOcean® radio interface:

Radiogram: EnOcean radiogram, bidirectional

Frequency: 868.3 MHz

Duty cycle: < 1%

Cyclic transmission/reception intervals

Communication cycle

10 min

Transmission power

< 10 mW

Illumination strength

Min. 150 lux recommended

Operating range

Radio:
Occupancy sen-
sor:

Approx. 30 m in buildings (depending on building 
structure)
Approx. 10 m

Housing

Plastic housing, RAL 9010 (pure white), 7001
Other colors on request

Protection class

III

Degree of protection

IP30

Ambient temperature

0..50 °C

Ambient humidity

During operation: 20..85% r.h., non-condensing
Out of operation: 5..90% r.h., non-condensing

Summary of Contents for RPW414P-FTL

































Reviews: