KidKraft GREYSTONE COTTAGE Installation And Operating Instructions Manual Download Page 3 | Manualshive

Page: 3 / 52

background image

Part Identification Key

On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.

Key Number:

The first two digits

represent the step number. The third
digit represents the piece. Note that
if the part is used in multiple steps
then the number only reflects the
first step it is used in.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

Proper Hardware Assembly
Lag screws require drilling pilot holes to
avoid splitting wood. Only a flat washer
is required. For ease of installation
liquid soap can be used
on all lag-type screws.

For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.

Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.

Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.

This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.

Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get
help!

Check that assembly is square
before tightening bolts.

Use a measuring tape to assure
proper location.

Check that set or assembly is properly level
before proceeding.

Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of  wood.

This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.

Use

Help

Use

Help

Measure

Distance

Square

Assembly

Use

Level

Pre-drill 1/8” & 3/16” Bit

Tighten

Bolts

CAUTION – Protrusion Hazard

Keys to Assembly Success

Tools Required

• Carpenters Level
• Carpenters Square

• Claw Hammer
• Tape Measure

• Standard or Cordless Drill
• Pencil

• Safety Glasses
• Adult Helpers

Quantity

Key Number

Part Description,
Part Size

2X 012 Post 2 x 4 x 83”

No

Yes

Lag Assembly

Bolt Assembly

Flat Washer

Lag Screw

Hex Bolt

Lock
Washer

Flat
Washer

Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes

T-Nut
(Hammer into place)
Do not crush wood!

If Bolt protrudes
beyond T-Nut

Use an extra
flat washer

3

[email protected]

3

«
1
2
3
4
5
...
»

Summary of Contents for GREYSTONE COTTAGE





















































Reviews:

No comments

Related manuals for GREYSTONE COTTAGE

Brand: JDS Uniphase Pages: 144

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 14

Brand: Omlet Pages: 60

Brand: J.ASSY Pages: 17

Brand: PAS Systems International Pages: 16

Brand: QualArc Pages: 2

Ascension B17 Series

Brand: Petzl Pages: 4

Brand: Kett Pages: 40

Brand: Magicfx Pages: 12

PERIOFLOW EL-354

Brand: EMS Pages: 68

Brand: KaVo Dental Pages: 64

Brand: Koehler Pages: 12

Brand: Sonotec Pages: 6

Brand: Beta Pages: 12

Brand: Robert Juliat Pages: 48

Brand: LIGHTSIDE Pages: 8

Brand: Larson Davis Pages: 16

Ecoline EL-900RGB

Brand: Laserworld Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands