manualshive.com logo in svg

KidKraft F24935, Installation And Operating Instructions Manual

Share
Download
KidKraft F24935 Installation And Operating Instructions Manual Download Page 20

 20 

Details

SHEET 1 OF 9

A

SIZE DWG.  NO.

REV.

SCALE:1:50

WEIGHT: 

Pre-drill using 3/16" drill bit for 1/4 x 2½ Lags

Use #8 x 7/8" Truss screws for the Jamb Mounts

Do not cover the 2 holes with Jamb Mounts

WL5

x 4 per 

side

1 x  

End Panel Assembly 1-1/4 x 42 x 87”

2 x 

Narrow Panel 1-1/4 x 22 x 87”

Wood Parts

Hardware

8 x 

1/4 x 2-1/2” Wafer Lag

WL5

Step 2: Frame Assembly 

Part 2

B:

  Place (2622) End Panel Assembly between 2 (2677) Narrow Panels noticing the panel orientations.  The 

tops and bottoms of the panels should be flush.   Make sure the panels are square then using the pilot holes as 

a guide pre-drill with a 3/16” drill bit and fasten the back (2677) Narrow Panel to (2622) End Panel Assembly and 

(2622) End Panel Assembly to the front (2677) Narrow Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags per side.  (fig. 

2.4, 2.5 and 2.6)

WEIGHT: 

SHEET 3 OF 8

REV.

A

DWG.  NO.

SIZE

SCALE:1:50

•Grooves in Panels face inward

•Front of fort is wider side

3-PAN.CONNECT B1

Left Side

2677

2622

Flush

Flush

Notice back 

(2677) Narrow 

Panel overlaps 

(2622) End 

Panel Assembly

WL5

WL5

Notice (2622) 

End Panel 

Assembly 

overlaps front 

(2677) Narrow 

Panel

Front

Back

2677

Top View

Left Side

Fig. 2.4

2622

Fig. 2.5

2677

Fig. 2.6

2677

Back

2677

Front

Flush

Flush

2622

Left Side

Summary of Contents for F24935


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands