manualshive.com logo in svg

KidKraft Cedar Summit Adventure Ridge Playset, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit Adventure Ridge Playset Installation And Operating Instructions Manual Download Page 20

1 x 

Slide End Panel 1-1/4 x 37 x 92”

1 x 

Narrow Back Panel 1-1/4 x 21-1/2 x 92”

1 x 

Narrow Front Panel 1-1/4 x 21-1/2 x 92”

Wood Parts

022

Step 2:  Slide Wall Assembly

A:

  Place (021) Narrow Back Panel against the left side of (022) Slide End Panel noticing panel orientation.  The 

tops and bottoms of the panels should be flush and panels square.   Pre-drill with a 3/16” drill bit, then fasten 

(021) Narrow Back Panel to (022) Slide End Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 2.1 & 2.2)

B:

  Place (023) Narrow Front Panel against the right side of (022) Slide End Panel noticing panel orientation.  

The tops and bottoms of the panels should be flush and panels square.   Pre-drill with a 3/16” drill bit, then fasten 

(022) Slide End Panel to (023) Narrow Front Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 2.1 & 2.3)

Fig. 2.2

Fig. 2.1

Hardware

8 x 

1/4 x 2-1/2” Wafer Lag

WL5

021

023

Fig. 2.3

A

B

A

B

A

B

Notice (021) Narrow 

Back Panel overlaps 

(022) Slide End Panel

Flush

Flush

022

022

021

023

WL5

023

022

Notice (022) Slide End 

Panel overlaps (023) 

Narrow Front Panel

Flush

021

 20 

 

  

Summary of Contents for Cedar Summit Adventure Ridge Playset


































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands