Kicker PWRA411 Manual Download Page 8

Page 8 of 10 

Troubleshooting the Kicker Integrated Systems 

If you experience a problem once the Subwoofer is installed use this guide to locate the trouble. 

The radio is working, but the Subwoofer is not working: 

Check the battery voltage to make sure it is not discharged below 11 volts.

Check the negative battery cable to see if it has been securely tightened back on the battery.

Check the inline fuse located near the battery to make sure it is plugged in completely, and not
blown.

Check the 12Volt power-connector near the firewall to make sure it is plugged in securely.

Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely.

Check the ground wire connection to make sure it is tightly secured to the proper ground in the
vehicle.

Check the audio input signal connection to make sure it is secure and connected to the proper
wiring.

Test with different music in case there is no low frequency audio in the initial sound check.

There is a buzz or rattle noise that accompanies the 

low frequency element of the music: 

Check for a connector or any other object that could be very near the subwoofer or the enclosure.

Check the subwoofer enclosure mounting brackets to make sure they are secure.

There is a problem with the multi-channel stereo amplifier: 

Check the battery voltage to make sure it is not discharged below 11 volts.

Check the negative battery cable to see if it has been securely tightened back on the battery.

Check the inline fuse located near the battery to see if it is plugged in completely and not blown.

Check the multi-pin connectors at the back of the radio and at the amplifier chassis to make sure
they are plugged all the way in.

Check the ground wire connection to make sure it is tightly secured to the proper ground in the
vehicle.

Summary of Contents for PWRA411











Reviews: