background image

 

 Locate the factory module bracket and remove the two nuts securing it. Fig 27 

 Pry the module wire retainers from the factory bracket. Fig 27 

  Note: Depending on the vehicle trim level, there may be one or two modules 

attached to the bracket.  The module(s) will need to be relocated using the 
supplied relocation bracket in order for the subwoofer to be installed. 

  Note: Do not disconnect the module wiring.  Modules wiring is shown 

disconnected in some pictures only for clarity of installation. 

 Pry out the center portion of the plastic retainer securing the smaller module and then the outer portion.  

Remove the module from the factory bracket. Fig 28 

 
 
 
 
 
 
 

 

 
 
 
 

 

 If equipped, remove the larger module by snapping it out of the factory bracket. 

 Pull the factory module bracket from the metal and discard. 

 If equipped with two modules, slide the larger module into the relocation bracket first as shown in Fig 29 

 Using the supplied bolt and plastic fastener, install the smaller module over the top of the larger module 

as shown in Fig 30 

  Note: The connectors on the smaller module face the opposite direction as the 

connectors on the larger module. The smaller module mounts the same way 
regardless of whether or not there is a second module. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig 27 

Fig 28 

Fig 29 

Fig 30 

Summary of Contents for PSUTA15














Reviews: