background image

2

Kice Industries, Inc.

MAN-100-000-008

110722

1. Introduction

When you purchased your new Kice Rotary Airlock, you bought a dependable and quality-built product. 

The range of options and materials of airlocks manufactured by Kice should satisfy nearly every 

conceivable industrial airlock need.

We are proud of our products and the people at Kice who build them. At Kice, we start in our own 

foundry and follow the design and manufacturing standards that have proven superior for more than 

75 years.

This owner’s manual is intended as a guide for proper installation, operation and maintenance to keep 

your Kice airlock operating safely and efficiently on the job. Service and factory reconditioning 

information is also included for your benefit.

Sincerely,

Drew Kice

President

Kice Industries, Inc.

Warranty

The Company (Kice Industries, Inc.) warrants the equipment manufactured by the Company to be free 

of defects in material and workmanship for a period of one year from the date of shipment. Company 

agrees to repair or replace, at its option, any parts found to be defective in the opinion of the Company. 

Company is not liable for any costs in connection with the removal, shipment or reinstallation of said 

parts. This warranty does not apply to abrasion, corrosion, or erosion.

Purchaser agrees to look to the warranty, if any, of the manufacturer or supplier of equipment 

manufactured by others and supplied to the Company for any alleged defects in such equipment and 

for any damages or injuries caused thereby or as a result thereof.
  

PURCHASER SHALL BE RESPONSIBLE FOR COMPLIANCE WITH ELECTRICAL 

COMPONENT MANUFACTURER’S RECOMMENDATIONS, UNDERWRITERS CODE 

AND ALL SAFETY PRECAUTIONS.

 

The only warranty extended under this agreement is the above express warranty and there are no 

other warranties, express or implied, including warranties of merchantability, fitness for a particular 

purpose or otherwise which extends beyond the face hereof. The Company and its dealers shall not in 

any event be liable for consequential or incidental damages and this agreement provides purchaser’s 

sole and exclusive remedy. Any actions for breach of this agreement or warranty must be commenced 

within one year after the cause of action has occurred.

Summary of Contents for VJO Series
































Reviews: