background image

 Revision Date

4/22/2013

 Page 1 of 25

 

 

 

 

Vehicle Model  Sorento (Key Start)        

Accessory 

Remote Engine Start 

 

 

 

 

Model Year 

2014 ~                             

Dif

fi

 culty 

              ( B )                  

 

 

 

 

Part No. 

1U056  ADU00                

 

KIA Genuine Accessories

Instruction Symbols / De

fi

 nitions

Note: Diffi culty stated above refl ects the minimum level of expertise required to install the accessory

 

( A ) Customer      ( B ) Dealer Technician      ( C ) Master Technician

 

Denotes warnings that may lead to
serious physical injury or vehicle
damage. 

Denotes cautions to be taken to avoid
physical injury or electronic component
damage. 

Denotes cautions to be taken to avoid
vehicle and component damage.

Denotes quality processes to be
checked prior to moving to the
next step.

Denotes specifi c tools that are neces-
sary to complete the step.

Denotes instructional steps
necessary to complete the 
process.

Denotes safety equipment required to be used 
such as a mask, goggles, rubber
gloves, and hearing protection.

N
O
T
E

Notes to the Installer: 

 

 

 

 

Read the entire installation manual prior to beginning the installation of the
accessory. 
 

 

 

 

Factory wire harness colors are subject to change, please use the speci

fi

 ed pin 

# in the harness connector to identify the correct wire for T-Tap installation.

Ensure that the vehicle is properly protected in the area that the accessory is to 
be installed.
 

 

 

 

 

 

 

To prevent vehicle damage, never place tools on top of painted surfaces, seats, 
dash pad, console or 

fl

 oor carpet / mat. 

 

 

 

 
Always wear appropriate safety gear to include gloves and eye protection when 
required. 

       

 
To prevent stress on the remote start wire harness, ensure the tilt/telescopic 
steering column is fully extended, if equipped.

Ensure the transportation fuse is properly installed before performing the 
function check on page 17.  

Technical Support

For Authorized Dealers - 

(800) 667-5176

Hours:

 9:00 a.m. - 5:30 p.m. EST Monday - Friday

            

Basic Required Hand Tools

Mask

Rubber Gloves

Hearing Protection

Goggles

Ensure vehicle is equipped with automatic transmission, power door locks 
and power windows.  If the vehicle is not equipped with these options, do 
not proceed.  Ensure vehicle does NOT have SMART KEY.

 

!

P/N: 4280516, Rev. A

 

 Ratchet

#2 Phillips
Screwdriver

Trim Tool

Wire Cutter

Pliers

 10 mm Socket

Alcohol Cleaner / 
Clean Cloth

Extension

Torque Wrench

Tape Measure

Summary of Contents for 1U056 ADU00


























Reviews: