Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
Toggle
®
Tables
Triple Motor C-Leg Height-Adjustable Square Shoe Base, Model SS
October 2019
1. Carefully remove contents from
packaging, set out on a soft, clean
surface and refer to Figures 1, 2 & 3
to identify the parts required for
assembly.
End C-Leg Assembly
(short end of table)
Note:
Two different lengths of
cross-support tubes and leg-to-leg
spanners are supplied. The short
end of the table uses four short
cross-support tubes and two short
leg-to-leg spanners (Figure 2).
ATTENTION:
Following assembly,
table must be “zero set” prior
to being placed into service
.
Failure to do so can cause table to
malfunction.
Table “Zero Setting”
:
Press and hold the Up button for two seconds
then release. Next, press and hold the Down button until table has
reached its lowest position then release Down button. Then, press the
Down button again and hold for approximately 10 seconds. The table
now re-set at its “Zero Setting” position and is ready to operate.
Motor-Operated Furnishing
-FOR COMMERCIAL USE ONLY-
2. Start assembling the C-leg to be
placed on the short end of the
table by positioning two shorter
cross-support tubes (with mounting
tabs facing down and facing inwards),
and one C-leg end support tube in
position as illustrated in Figure 1.
Place a leg column assembly over
the three support tubes and align six
mounting holes of the leg column
mounting base with appropriate
mounting holes of the three tubes as
illustrated. The C-leg end support
tube contains three mounting holes
but only the two non-user side holes
are used. Make sure the tube has the
longer end with one unused mounting
hole facing the user side as illustrated
in Detail A. Using six M8 x 12 button
head machine screws torqued to
9.5 ft/lb, secure the flange of the leg
column to the three support tubes
(Figure 1).
3. Assemble the C-leg foot to the leg
column by first positioning a plastic
foot plate over the mounting location
on the leg column. The foot plate
must be oriented so the raised flange
faces into the column, to nest the foot
plate into place. Next, position a foot
over the foot plate and leg column as
illustrated, with the mounting holes
of the foot aligning with those of the
leg column. It is important that the
longer end of the C-leg foot face the
user side. Once the foot is correctly
oriented, secure the foot to the leg
column with four M6 x 35 socket
head cap screws. Torque to 7.5 ft/lb
(Figure 1).
4. Position the two shorter leg-to-leg
spanners with their channel openings
face up, then slide both spanners into
the open ends of the cross-support
tubes installed under the leg column
base. Next slide a cross-support tube
(matching the same length as at the
opposite end of the leg-to-leg
spanner) onto each end of the
leg-to-leg spanners (with mounting
tabs face down and facing inward).
Do not secure the support tubes to the
spanners with set screws at this time
(Figure 1).
Figure 1
M6 x 35
socket head
cap screws
M8 x 12
button-head
machine screw
M6 x 35
socket head
cap screw
cross-support
tubes (short)
leg-to-leg
spanners
(short)
USER
SIDE
USER
SIDE
cross-support
tubes (short)
adjustable
glide
C-leg
foot
foot
plate
M8 x 12
button-head
machine
screw
leg column
assembly
(at short end)
mounting
flange of
motor
housing
C-leg
end-support
tube
set screw
holes
square shoe
tabletop (short end)
(shown for reference)
Detail A
C-leg
end-support
tube
M8 x 12
button-head
machine
screw