Installation and Operation of Electric Convection Oven
INSTALLATION INSTRUCTIONS
A. QUALIFIED PERSONNEL
The oven should be placed in an area that is free
from drafts and accessible for proper operation
and servicing.
These installation instructions are for the use of
qualified
installation and service personnel only. Installation or
service by other than
qualified personnel may result in
damage to the oven and/or injury to the operator.
Refer to the Oven Placement Clearances Chart
before installing the oven.
Qualified installation personnel are those individuals,
firms,companies or corporations which either in personor
throughan agent is engaged in and responsible for:
OVEN PLACEMENT CLEARANCES CHART
COMBUSTIBLE
NON-COMBUSTIBLE
Right Side
Left Side
Rear
1"
1"
3"
8"
0"
0"
3"
8"
•
The installation of electrical wiring from the electric
meter, main control box or service outlet to the
electrical
appliance.Qualified installation personnel
must be familiar withall precautions required and
have complied with all requirements of state and
local authorities having jurisdiction. See: National
Electrical Code, ANSI/NFPA70.
Floor
It is also important not
to obstruct the natural flow of
ventilation air if the oven is to operate properly. This
oven should not be installed on a curb base or sealed
to the wall. Either condition can restrict the flow of air to
or prevent proper ventilation of the blower motor. The
blower motor has a thermal protection device,which will
trip, because of excessive ambient temperatures at the
back of the oven. This condition should be corrected
immediately to avoid damaging the oven permanently.
B. DELIVERY AND INSPECTION
KFEdoes everything with in its power
to insure you received your oven in good condition.
They are strapped down on heavy wooden skids and
Surrounded by heavy
“tri-wall” carton stop revent shipping
damage. They have all been carefully inspected before
they were packaged and consigned to the carrier.
Before making any connections to the oven, check the
specification plate to be sure the oven specifications
concur with the voltage and phase to be supplied to
the oven.
Upon delivery of your KFEoven:
Look over the shipping container,carefully noting any
Exterior damage on the delivery receipt, which must
also be signed by the driver/ delivery person.
The
specification plate islocated behind the lower front
panel.To access the
specification plate,loosen the four
screws below the doors, and pull the panel outward.
Uncrate and check for any damage, which was not
evident on the outside of the shipping container.
This is called concealed damage.The carrier must
be notified within fifteen (15) days of the delivery
of the oven and the carton, skid and all packaging
materials must be retained for inspection.
Thespecificationplatebearingtheoven’sserialnumber
is attached to the underside of the upper ledge above
the control panel.
D. ELECTRICAL CONNECTIONS
KFE cannot assume liability for
Loss or damage suffered in transit. The carrier assumes
full responsibility for delivery in good order when the
shipment was accepted. However, we are prepared to
assist you in filing your claim.
The oven is supplied for connection to a 208, 240, 440
or 480 volt grounded circuit. The electric motor, oven
lights,indicatorlightsandcontrolcircuitsareconnected
internally and require no secondary power supply.
Before making any connections to these units, check
the specification plate to assure that the voltage and
phase of the oven is compatible with the electrical
supply. When installing, all ovens must be electrically
grounded in accordance with local codes or in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70 (in Canada
– CSA Std. C22.1).
Wiring diagrams are located in the control compartment
C. LOCATION OF THE OVEN
Proper planning and placement of the oven will give you
the best results in terms of long-term user convenience
and satisfactory performance. We urge you to give
adequate thought in the placement of your oven prior
to its arrival.
Summary of Contents for KF-COE-208
Page 13: ......
