Keysight U1401B User'S And Service Manual Download Page 75

Page: 75 / 159

Making Measurements

Keysight U1401B User’s and Service Guide

1 ms peak hold

This function allows the measurement of peak voltage for analysis of components

such as power distribution transformers and power factor correction capacitors.

The peak voltage obtained can be used to determine the crest factor.
Crest factor = Peak value/True-rms value
To measure the half-cycle peak voltage:

Press

for more than one second to toggle 1 ms peak hold mode on or off.

Press

to show the peak

or peak– value after activating the peak mode.

The

DH MAX

annunciator indicates the peak+ value while the

DH MIN

annunciator indicates the peak– value. See

Figure 3-10

on page 75.

If the reading is

, press

to change the measurement range and restart

the peak value measurement.

While the peak hold mode is on, you can press

at any time to restart the

peak value measurement.

Figure 3-10

1 ms peak hold mode

Press

1 s

Press

Press
to restart

Press
to change

range

Press

1 s

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands