Keysight U1401B User'S And Service Manual Download Page 119

Page: 119 / 159

Application Examples

Keysight U1401B User’s and Service Guide

119

The cutoff voltage of a p-channel JFET

To determine the cutoff voltage of a p-channel JFET:

Connect the red input probe lead to the drain.

Connect the black input probe lead to the source.

Connect the red output alligator lead to the gate terminal through a 100 k

resistor, and connect the black output alligator lead to the black input probe

lead.

Gradually decrease the voltage output from +

00.000

V to +

15.000

V. The R

value will increase correspondingly (

Figure 5-12

on page 119).

Observe at what point the resistance reading becomes

; the voltage bias

level at that point would be the cutoff voltage for the p-channel JFET.

Figure 5-12

P- Channel JFET

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands