manualshive.com logo in svg

Keysight P9370A, Startup Manual, Page: 30 / 38

Share
Download
Keysight P9370A Startup Manual Download Page 30

 3-6                                                                                           Keysight Technologies Startup Guide

 

Safety and Regulatory Information
Regulatory Information

3-

Instrument Markings

Some instrument markings may not appear on your analyzer.

This symbol marks the ON position of the power line switch.

This symbol marks the ON position of the power line switch.

This symbol marks the standby position of the power line switch.

This symbol marks the OFF position of the power line switch.

This symbol marks the OFF position of the power line switch.

The instruction documentation symbol. The product is marked with this symbol when it 

is necessary for the user to refer to the instructions in the documentation.

This symbol indicates separate collection for electrical and electronic equipment, 

mandated under EU law as of August 13, 2005. All electric and electronic equipment 

are required to be separated from normal waste for disposal (Reference WEEE 

Directive, 2002/96/EC).
This symbol is used to identify a terminal which is internally connected to the product 

frame or chassis.

The CE mark is a registered trademark of the European Community (if accompanied by 

a year, it is the year when the design was proven). This product complies with all 

relevant directives.

The Keysight email address is required by EU directives applicable to our product.

The CSA mark is a registered trademark of the CSA International.

This is a symbol of an Industrial Scientific and Medical Group 1 Class A product. 

(CISPR 11, Clause 5)

Summary of Contents for P9370A







































Reviews:

No comments