Keysight N9923A User Manual Download Page 61

Page: 61 / 276

Keysight N9923A Handheld Analyzer
User’s Guide

4 Time Domain – Option 010

With NA Mode, Time Domain Reflectometry (Opt 010), frequency information is
used to calculate and display measurements with time as the horizontal

display axis. The response values appear separated in time allowing a different
perspective of the test device's performance and limitations.

NA Mode settings that are NOT unique to Time Domain are documented in

Chapter 3, “NA (Network Analyzer) Mode”, on page 37

In This Chapter

Time Domain (Transform) Settings

Trace Settings

“Overview” on page 63

“Transform Settings Table” on page 64

“Frequency Range and Points” on page 64

“Stimulus (Mode)” on page 65

“Set Frequency Lowpass” on page 65

“Start/Stop Time” on page 65

“Distance Units” on page 66

“Window Layout” on page 66

“Transform Window” on page 66

“Window Settings” on page 67

“Line Loss and Velocity Factor” on page 69

“Data Chain” on page 70

“Gating Type” on page 73

“Transform Enable” on page 71

“Gate Enable” on page 71

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 61 / 276

Search results

Summary of Contents for N9923A

Reviews: