manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 40 / 276

Share
Download
Keysight N9923A User Manual Download Page 40

 40                                                                                                                     Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

S21 and S12 transmission measurements are used to measure the loss or gain 
through a DUT over a specified frequency range. Both ends of the DUT must be 

connected to the FieldFox. The FieldFox signal source is transmitted out one of 
the test port connectors, through the DUT, and into the other test port 
connector

How to measure S-parameters

1.

Press 

Preset

 then 

Preset

2.

Press 

Measure 1

 then choose from the following:

—

S11

 Reflection measurement at port 1.

—

S21

 Forward 2-port transmission measurement.

—

S12

 Reverse 2-port transmission measurement. May require an 

option. 

—

S22

 Reflection measurement at port 2. May require an option.

OR

 select a multi-trace configuration. Learn more on 

“Multi-Trace 

Configurations” on page 43

.

3.

Press 

Freq/Dist

 then either 

Start

 and 

Stop

 or 

Center

 and 

Span

 to enter a 

Frequency Range for the measurement.

4.

Press 

BW 2

 then 

IFBW

 to select the IF Bandwidth for the measurement. 

Narrower bandwidths require more time to sweep, but lowers trace noise.

5.

Press 

Sweep 3

 then 

Resolution

 to select the number of data points for the 

measurement. More data points require more time to sweep.

6.

Press 

Cal 5

 to calibrate the measurement. Learn more in 

“How to Perform 

a Calibration” on page 104

.

7.

All other settings can be made AFTER calibration without compromising 

measurement accuracy.

Mixed-Mode S-Parameters

In NA Mode ONLY, mixed-mode S-parameters (also known as Balanced 
measurements) are available with Option 212. 

Because the FieldFox has only two test ports, only reflection measurements are 
available. Connect the balanced input or output of your DUT to the FieldFox 

ports 1 and 2

For highest accuracy, a Full 2-port calibration is required.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments