manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 104 / 276

Share
Download
Keysight N9923A User Manual Download Page 104

 104                                                                                                                     Keysight N9923-90001 User’s Guide

Calibration for NA, CAT, and VVM Modes

— A 

THRU

 standard is used during some calibration steps to connect PORT 1 

to PORT 2 in place of the DUT. A Flush THRU connection can be made 

when cables that connect with the DUT can mate with each other. Learn 
more in 

“Mechanical Cal” on page 108

. Otherwise, any reasonably short 

cable can be used as a THRU standard.

Calibration Reference Plane

 is the point (or points) at which the DUT and cal 

standards are connected during a calibration. This can be at the FieldFox test 
port connectors, or at the end of jumper cables or adapters. 

CalReady

Every FieldFox contains a factory calibration that was performed at the port 1 
and port 2 connectors, with -15 dBm input power, over the entire frequency 
range of the FieldFox using a number of data points that allows reasonable 

interpolation over the FieldFox frequency range. 

This calibration, known as CalReady, allows you to immediately make 

measurements of a DUT that is connected directly at the test ports (PORT 1 
and/or PORT 2). CalReady corrects measurements when the FieldFox is turned 
ON and when a measurement is created with no other correction in place.

When measuring a DUT using a jumper cable or adapter - NOT a direct 
connection to a test port connector – then a QuickCal or Mechanical Cal is 
recommended. CalReady can also be used to check the integrity of the jumper 

cable that is attached to the test ports. 

CalRdy

 is shown when a measurement is corrected using CalReady. 

You can change the properties of the CalReady calibration. Learn more in 

“CalReady” on page 104

.

Learn how to see when your factory CalReady calibration was performed in 

“System Information” on page 235

. 

How to Perform a Calibration

In CAT, NA, or VVM Mode, press 

Cal 5

.

Press 

Esc

 at any time to end the calibration process.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments