Keysight N7744A User Manual Download Page 31

Page: 31 / 105

Front Panel Indicators

During operation, you may notice the following LED indicators:

Figure 16

Front Panel Indicators

Connecting to the Instrument

Connecting to the Instrument - Overview

When you are first connecting the instrument, we recommend you use

the

Keysight

Connection Expert included with the

Keysight

I/O

libraries

(available on the CD supplied with the instrument, or from

www.

eysight

.com

Connecting over USB

N O T E

The screenshots show the

Keysight

N7745A Multiport Power Meter. The same

procedure applies when connecting an

Keysight

N7744/7/8A Multiport Power

Meter, an

Keysight

N7751/2A Optical Attenuator and Power Meter, or an

Keysight

N7761/2/4/6/8A Optical Attenuator or an

Keysight

N7711/4A

Tunable Laser

System Source or an N773x Optical Switch.

If it is not already running, start the

Keysight

Connection Expert

software.

Getting Started

Keysight N774x Series

Summary of Contents for N7744A










































































































Search results

Summary of Contents for N7744A

Reviews:

Related manuals for N7744A

Brands by name

Popular brands

Keysight N7744A, User Manual

Search results

Summary of Contents for N7744A

Reviews:

Related manuals for N7744A

Brands by name

Popular brands