Keysight N5221BU-677 Page 19 Installation Note Download | Manualshive

Page: 19 / 54

background image

Installation Note N5222-90129 19

Installation Procedure for the Upgrade

Step 8. Assemble the A24 Mixer Brick and A22 Splitter Assemblies

1.

Follow the instruction shown in

. New parts are listed

in

Table 2 on page 11

of this document.

Figure 2

A24 Mixer Brick Assembly (0515-0372, 0515-1410, 5087-7829)

IMPORTANT!

The A22 splitter (5087-7139) and N5222-20007,

N5222-20008, and N5222-20009 cables are only used with a legacy

HMA26.5 p/n: 5087-7765. If your PNA has a new N5240-60101 assembly

installed, then set aside these parts as spares for use in other PNAs with

the older HMA26.5 or discard. If you are unclear which HMA26.5 assembly

your PNA has installed, refer to

Figure 1 on page 7

«
...
17
18
19
20
21
...
»

Summary of Contents for N5221BU-677























































Reviews:

No comments

Related manuals for N5221BU-677

Brand: WMD Pages: 5

Brand: E.M.L . Pages: 70

Electone Stagea ELS-01

Brand: Yamaha Pages: 84

Brand: TB-Electronics Pages: 40

Brand: Yamaha Pages: 91

Brand: EarthQuake Pages: 12

Brand: Yamaha Pages: 20

Brand: Bleeplabs Pages: 2

Brand: MasterSounds Pages: 12

Brand: Endorphines Pages: 2

Brand: Stagg Pages: 56

Brand: Clavia Pages: 29

Brand: Clavia Pages: 40

Brand: Clavia Pages: 55

Brand: Clavia Pages: 76

Brand: Clavia Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands