Keysight N5166B Manual Download Page 21

Page: 21 / 24

Security Features and Document of Volatility

Procedure for Declassifying a Faulty Instrument

If the instrument is not functional, and you are unable to use the security

functions, you may physically remove the Processor board and Solid State

Drive (SSD), if installed.
For removal and replacement procedures, refer to the

Service Guide

for your

instrument.
Once the Processor and SSD assemblies have been removed, proceed as in

Table 7-1

below:

Table 7-1

Assembly Disposal Procedures

Assembly

Procedure

Processor (CPU) Board

Either

Discard the processor board and send the instrument to a repair facility. A new Processor

Board will be installed, then the instrument will be repaired and calibrated. If the instrument

is still under warranty, you will not be charged for the new Processor Board.

If you have another working instrument, install the Processor Board into that instrument and

erase the memory. Then reinstall the Processor Board back into the non-working instrument

and send it to a repair facility for repair and calibration. If you discover that the Processor

Board does not function in the working instrument, discard the Processor Board and note

that it caused the instrument failure on the repair order. If the instrument is still under

warranty, you will not be charged for the new Processor Board.

A4 Solid State Disk Drive

(SSD) Assembly
(Vector Instruments Only)

Either

Discard the SSD assembly and send the instrument to a repair facility. A new assembly will

be installed, then the instrument will be repaired and calibrated. If the instrument is still

under warranty, you will not be charged for the new assembly.

If you have another working instrument, install the SSD assembly into that instrument and

erase its memory. Then reinstall the assembly back into the non-working instrument and

send it to a repair facility for repair and calibration. If you discover that the assembly does not

function in the working instrument, discard the assembly and note that it caused the

instrument failure on the repair order. If the instrument is still under warranty, you will not be

charged for the new assembly.

Summary of Contents for N5166B

























Search results

Summary of Contents for N5166B

Reviews:

Related manuals for N5166B

Brands by name

Popular brands

Keysight N5166B, Manual

Search results

Summary of Contents for N5166B

Reviews:

Related manuals for N5166B

Brands by name

Popular brands