Keysight Technologies NFA X-Series Getting Started And Troubleshooting Manual Download Page 22

Page: 22 / 99

22 Keysight NFA X-Series Getting Started and Troubleshooting Guide

Quick Start
Using the U7227-Series USB Preamplifiers in Noise Figure Measurements

Initial Connection to the Signal Analyzer

The U7227-Series USB Preamplifier is powered via a USB connection from the

signal analyzer. To connect it to the analyzer, follow the steps below.

Connect the Output port of the USB preamplifier to the RF Input port of

the signal analyzer.

Connect the USB port (Type-B) of the USB preamplifier to the USB port

(Type-A) of the signal analyzer either in the front panel or in the rear panel

using a USB cable. You can “hot plug” the USB preamplifier into the

analyzer’s USB port at any time.

Figure 1-2

shows the U7227-Series USB Preamplifier connection in the two

stages of the noise figure measurement. While the USB preamplifier is plugged

into one of the analyzer’s USB ports, the analyzer will consider it to be in the

RF input signal path and will apply the gain settings and other calibration data

of the USB preamplifier to the measurements.

Figure 1-2

U7227-Series USB Preamplifier and Analyzer Connection in the Two Stages of

Noise Figure Measurement

Before connecting a signal to the input port of the U7227-Series USB

Preamplifier, make sure the USB preamplifier can safely accept the signal

level provided. The signal level limits are marked next to the Input

connectors of the USB preamplifier.

The USB connections of the U7227-Series USB Preamplifier and the

keyboard to the signal analyzer must be separated from each other; for

example, the USB preamplifier connects through the front panel while the

keyboard connects through the back panel.

Summary of Contents for NFA X-Series




































































































Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands

Keysight Technologies NFA X-Series, Getting Started And Troubleshooting Manual

Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands