Keysight Technologies N774 C Series User Manual Download Page 52

Page: 52 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

N774xC Series User Interface

Figure 14

shows the N7745C user interface with various tabs highlighted.

The same user interface is applicable for N7744C the instrument.

Figure 14

N7745C User Interface

The N774xC series user interface has the various tabs that help the user to

control the N7744/45C instruments:
•

Home

– This tab displays the various instrument settings. For details,

refer

How to Get Current Instrument Settings?

on page 67.

•

Control Instrument

– This tab allows you to set the parameters to

control the instrument. For details, refer to

Controlling N774xC

Instruments

on page 54.

•

Get Image

– This tab allows you to capture a screen of the

Control

Instrument

window. The image is saved in PNG format in your PC. For

details, see

How to Capture an Image of the Graph?

on page 68.

Summary of Contents for N774 C Series





















































































Search results

Summary of Contents for N774 C Series

Reviews:

Related manuals for N774 C Series

Brands by name

Popular brands

Keysight Technologies N774 C Series, User Manual

Search results

Summary of Contents for N774 C Series

Reviews:

Related manuals for N774 C Series

Brands by name

Popular brands