Keysight Technologies N774 C Series User Manual Download Page 67

Page: 67 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

How to Use Auxiliary Functions

How to Get Current Instrument Settings?

The

Home

tab on the N774xC user interface displays the current

instrument settings.

This tab displays the following settings:
•

Description

– Displays the instrument description such as instrument’s

model no., serial no., firmware version and description of the current

instrument.

•

VISA Instrument Address

– Displays VISA instrument addresses of the

current instrument.

•

LAN Details

– Displays LAN configuration details of the current

instrument.

NOTE

Please note that the

Home

tab does not allows the user to change the

displayed instrument settings.

Summary of Contents for N774 C Series





















































































Search results

Summary of Contents for N774 C Series

Reviews:

Related manuals for N774 C Series

Brands by name

Popular brands

Keysight Technologies N774 C Series, User Manual

Search results

Summary of Contents for N774 C Series

Reviews:

Related manuals for N774 C Series

Brands by name

Popular brands