Keysight Technologies N5221BU-605 Installation Note Download

Page: 71 / 88

Installation Note N5222-90114 71

Installation Procedure for the Upgrade

Step 42. Replace the Front Panel’s Lower Dress Panel

Before the front panel’s lower dress panel can be replaced, the 2-port lower

dress panel and the lower front panel label must be removed from the front

panel assembly. Refer to

Figure 42 on page 71

. New parts are listed in

Table 2

on page 11

Remove the 2-Port lower front panel label (item



Remove the 10 screws (save the screws for reuse) from the 2-port dress
panel and remove the dress panel (item

②

and

③

respectively).

Reassemble the front panel’s lower dress panel assembly with the new

4-port front frame (N5240-00009) by reversing the order of step

in the

instructions previously followed.

Figure 42

Replacing the Front Panel’s Lower Dress Panel and label (N5240-00009)

IMPORTANT!

To avoid possible damage to the lower front panel overlay

(label), do not attempt to attach to lower front panel label until

“Step 44.

Install the New Lower Front Panel Overlay” on page 72

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands