Keysight Technologies N5221BU-605 Installation Note Download

Page: 31 / 88

Installation Note N5222-90114 31

Installation Procedure for the Upgrade

Step 16. Assemble the A24 Mixer Brick and A22 Splitter Assemblies

Follow the instruction shown in

Figure 10

and

Figure 11

. New parts are listed in

Table 2 on page 11

of this document.

Figure 10

A24 Mixer Brick Assembly (5087-7829, 0515-0372, and 0515-1410)

IMPORTANT!

The A22 splitter (5087-7139) and N5222-20007,

N5222-20008, and N5222-20009 cables are only used with a legacy

HMA26.5 p/n: 5087-7765. If your PNA has a new N5240-60101 assembly

installed, then set aside these parts as spares for use in other PNAs with

the older HMA26.5 or discard. If you are unclear which HMA26.5 assembly

your PNA has installed, refer to

Figure 1 on page 7

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands